TYAN S2927 Manual Download Page 61

Page: 61 / 88

http://www.tyan.com

3.8 PCI/PnP Menu

You can use this screen to view PnP (Plug & Play) BIOS Configuration

Menu. This menu allows the user to configure how the BIOS assigns resources
& resolves conflicts. Use the up and down arrow (

) keys to select an item.

Use the Plus and Minus (+/-) keys to change the value of the selected option.
The settings are described on the following pages.

BIOS Setup Utility

Main Advanced

PCI/PnP

Boot Security Chipset Exit

Advanced PCI/PnP Settings

WARING: Setting wrong values in below sections may
cause system to malfunction.

Clear NVRAM

Plug & Play O/S
PCI Latency Timer
Allocate IRQ to PCI VGA
Palette Snooping
PCI IDE BusMaster

[No]

[No]
[64]
[Yes]
[Disabled]
[Disabled]

Clear NVRAM during
System Boot.

←

→

Select Screen

↑↓

Select Item

+/- Change Option
F1 General Help
F10 Save and Exit
ESC Exit

Summary of Contents for S2927

























































































Search results

Summary of Contents for S2927

Reviews:

Related manuals for S2927

Brands by name

Popular brands

TYAN S2927, Manual

Search results

Summary of Contents for S2927

Reviews:

Related manuals for S2927

Brands by name

Popular brands