TYAN S2927 Manual Download Page 49

Page: 49 / 88

http://www.tyan.com

3.7.4 Super IO Configuration Sub-Menu

You can use this screen to select options for the Super I/O settings. Use the

up and down arrow (

) keys to select an item. Use the Plus and Minus (+/-)

keys to change the value of the selected option

BIOS Setup Utility

Main

Advanced

PCI/PnP Boot Security Chipset Exit

Configure SCH5017 Super IO Chipset

Onboard Floppy Controller

Serial Port1 Address
Serial Port2 Address
Chassis Intrusion Detect
Watchdog Mode

[Enabled]

[3F8/IRQ4]
[2F8/IRQ3]

[Disabled]
[Disabled]

Allows BIOS to enable
or disable Floppy
Controller.

←

→

Select Screen

↑↓

Select Item

+/- Change Option
F1 General Help
F10 Save and Exit
ESC Exit

Feature

Option

Description

Configure SCH5017 Super IO Chipset

Disabled

Onboard Floppy Controller

Enabled

Allow BIOS to enable or disable the
floppy controller.

3F8 IRQ4

3E8 IRQ4
2E8 IRQ3

Serial Port1 Address

Disabled

Allow BIOS to select Serial Port1
Base Addresses.

2F8 IRQ3

3F8 IRQ4

2E8 IRQ3

Serial Port2 Address

Disabled

Allow BIOS to select Serial Part2
Base Addresses.

Disabled

Chassis Intrusion Detect

Enabled

Enable/Disable the function of
chassis intrusion detection. When
chassis open event is detected,
BIOS will record the event.

Disabled

Watchdog Mode

Enabled

Enable/Disable watchdog mode.

Summary of Contents for S2927

























































































Search results

Summary of Contents for S2927

Reviews:

Related manuals for S2927

Brands by name

Popular brands

TYAN S2927, Manual

Search results

Summary of Contents for S2927

Reviews:

Related manuals for S2927

Brands by name

Popular brands