TYAN S2505T User Manual Download Page 2

Page: 2 / 57

http://www.tyan.com

Congratulations! .........................................................................................................

Hardware Specifications ............................................................................................

Software Specifications ..............................................................................................

Chapter 1: Introduction

Chapter 2: Board Installation

Chapter 3: BIOS Setup

Front Panel Connector .............................................................................................

CMOS Reset ............................................................................................................

IDE RAID Enable/Disable ........................................................................................

Onboard VGA Enable/Disable .................................................................................

FAN Connectors ......................................................................................................

CPU Frequency Ratio Jumpers ...............................................................................

Serial Port Connector ...............................................................................................

USB Connector ........................................................................................................

Wake-on-Ring, Wake-on-LAN .................................................................................

IDE RAID Connectors ..............................................................................................

Soft Power Connector Installation ............................................................................

Hardware Reset Switch Connector Installation ........................................................

Flash Utility ..............................................................................................................

Installation ..................................................................................................................

How to install our products right... the first time ..........................................................

Here are some safety tips ..........................................................................................

Quick Reference for Jumpers ....................................................................................

Map of Motherboard Jumpers ..................................................................................

Setting up Jumpers and Onboard Connectors .........................................................

Introduction to the BIOS Setup .................................................................................

Starting Setup ..........................................................................................................

Setup Keys ...............................................................................................................

Getting Help .............................................................................................................

In Case of Problems .................................................................................................

Setup Variations .......................................................................................................

Mounting the Motherboard in the Chassis ................................................................

Installing Memory .....................................................................................................

Removing a DIMM ...................................................................................................

Buffered vs. Unbuffered Memory ............................................................................

Suggested Memory Configurations ..........................................................................

Installing the CPU and Cooling Fan .........................................................................

Installing the CPU ....................................................................................................

Installing the Cooling Fan(s) ....................................................................................

Connecting IDE and Floppy Drives ..........................................................................

Connecting Floppy Drives ........................................................................................

Installing Add-on Cards ............................................................................................

Connecting PS/2, USB, and Serial Devices .............................................................

Connecting the Power Supply ..................................................................................

You are done! ...........................................................................................................

Frequently Asked Questions (FAQ) .........................................................................

.............................................................

.......................................................................

....................................................................

2.1
2.2
2.3
2.4
2.5
2.6

1.1
1.2
1.3

2.6-A
2.6-B
2.6-C
2.6-D
2.6-E
2.6-F
2.6-G
2.6-H
2.6-I
2.6-J
2.6-K
2.6-L
2.6-M

2.7
2.8

2.9

2.10

2.11
2.12
2.13
2.14
2.15

Table of Contents

Before you begin...

.................................................................... Page 4

Summary of Contents for S2505T


























































Search results

Summary of Contents for S2505T

Reviews:

Related manuals for S2505T

Brands by name

Popular brands

TYAN S2505T, User Manual

Search results

Summary of Contents for S2505T

Reviews:

Related manuals for S2505T

Brands by name

Popular brands