TYAN S2505T User Manual Download Page 11

Page: 11 / 57

Tiger 200T S2505T

2.6 Setting up Jumpers and Onboard Connectors

2.6-A. Front Panel Connector (J12)

Your chassis will usually come with connectors to install onto

the motherboard, such as HDD and Power LEDs. The Front

Panel Connector (J12) has been implemented for such purposes.

2.6-B. CMOS Reset (JP8)

If you have been locked out of your system because you forgot your password, or set the CMOS incor-

rectly, or have just finished flashing your BIOS follow the instructions below.

By following this procedure, you will erase your password and reset the CMOS.

Abbreviations

Reset

Rst

Pwr

Power

ground

switch

7 8

VCC+

12
14

13
15 16

3 4

1 2

HDD

ground

Pwr LED+

Slp LED+

switch

ground

no connect

VCC

no connect
no connect

17 18 DRIVER

no connect

GND

no connect

* default is

1-2

JP8

1-2

normal

2-3

clear

1. Power off the system
2. Close pins 2-3 on JP8
3. Wait about three seconds
4. Close pins 1-2 on JP8, then power on the system again

SPEAKER

Pinouts for certain connectors are available on the Tyan website:

http://www.tyan.com

Summary of Contents for S2505T


























































Search results

Summary of Contents for S2505T

Reviews:

Related manuals for S2505T

Brands by name

Popular brands

TYAN S2505T, User Manual

Search results

Summary of Contents for S2505T

Reviews:

Related manuals for S2505T

Brands by name

Popular brands