background image

2 | 

P a g e

 

 

3.

 

Fill up the Warranty Registration Card and 

mail it to the indicated address.    

 

 
 
 
 
 
 

GAS SAFETY REQUIREMENTS 

– 

T

WIN 

E

AGLES 

G

AS 

P

OWER BURNER

 

 
Each appliance is set and tested at the factory for the type of gas supply to be used. Identify the 

type of gas, either natural gas or LP gas and make sure that the marking on the data plate (rating plate) 
matches the gas being supplied to the Power Burner. The data plate is located on the panel behind the 
control panel of the Power Burner. Remove the drip pan to visually access the nameplate label from 
the front of the Power Burner.  A second label with model number and serial number is located under 
the right side of the control panel. 

 
All gas connections should be made by a qualified technician and in accordance with local 

codes and ordinances.  The  installation  must  conform with local codes or, in the absence of local 
codes, with either the national Fuel Gas Code, ANSI Z223.1/NFPA 54, or CAN/CGA-B149.1, Natural 
Gas Installation Code or CAN/CGA-B149.2, Propane Installation Code. 

 

WARNING:  
CHECK TO ENSURE THAT THE GAS SUPPLY HOSE DOES NOT COME IN 
CONTACT WITH ANY HOT SURFACE OF THE POWER BURNER. 
 
NEVER CONNECT THE POWER BURNER TO AN UNREGULATED GAS 
SUPPLY. 

 

GAS SAFETY REQUIREMENTS 

– 

T

WIN 

E

AGLES 

G

AS 

P

OWER BURNER 

(C

ONTINUED

)

 

 
L.P. GAS (LIQUIFIED PETROLEUM /PROPANE)

 

If your Power Burner is factory built for L.P., the regulator supplied is set for 10” water

 

column and is for use with L.P. gas only. The factory-supplied regulator must be used. 

 

L.P. GAS SAFETY REQUIREMENT 

 

The LP-gas supply cylinder must be constructed and marked in accordance with the 

Specifications for LP-gas Cylinders 

of the U.S. Department of Transportation (D.O.T.) or the National 

Standards of Canada 

CAN/CSA-B339, Cylinders, Spheres and Tubes for the Transportation of 

Dangerous Goods, and Commission, 

as applicable; and  

 

1. Provided with a listed overfilling prevention device.  
2. Provided with a cylinder connection device compatible with the connection for outdoor cooking 

appliances.  

Specifications 

Value 

Counter Opening Height 

11.50” 

Counter Opening Width 

22.00” 

Counter Opening Depth 

20.50” 

Btu 70,000 
NG Orifice Outer Ring 

#30 

NG Orifice Inner Ring 

#41 

LP Orifice Outer Ring 

#49 

LP Orifice Inner Ring 

#53 

Summary of Contents for TEPB24-B


















Reviews: