background image

TURFCO Service Quick Tip

 

 

 

T3000i/T3100 Weekly Preventative Maintenance Checklist 

Page 

1 of 1

 

Questions? Call Turfco at 1-800-679-8201

 

T3000i/T3100 Daily Preventative Maintenance Checklist 

 

WHAT? 

Daily Preventative Maintenance for the 
T3000i/T3100. 

 

WHY? 

Preventative maintenance.

 

  

Checklist 

 

Clear any fertilizer and debri off of the unit every day with 
a blower or pressurized air hose. Key areas include: 

o

 

Around the axel (Remove the front hood) 

(FIGURE 1)

 

o

 

Around and under the engine 

o

 

Inside and under the hopper (Move hopper gate 
open and closed while cleaning) 

o

 

Around the transmission 

 

Clean with water when necessary (i.e. high humidity days or once a 
week) WHEN CLEANING WITH WATER BE THOUROUGH ENSURING ALL 
FERTILIZER IS REMOVED FROM THE UNIT. Water mixed with fertilizer 
sitting on the unit for extended periods of time is very harmful to any 
equipment. Blow off the unit with air after cleaning with water. 

o

 

Variable speed pulley 

 Clean the pulley with water as you 

switch between the wide and narrow setting on the unit.  DO 
NOT USE A LUBRICANT ON THE PULLEY.  Blow the water out of 
the pulley with air when done cleaning. 

(FIGURE 2)

 

 

Check you spray system filter (wear proper personal protective 
equipment when cleaning the spray system (PPE) 

 Turn the ball valve 

to off and remove your filter.  Clean with water as necessary (Do not use 
high pressured air or water to clean the filter.  It can damage the filter 
screen). Replace the filter and turn the ball valve back to on. 

(FIGURE 3)

 

 

Check your engine and transmission oil levels 

 

 
Completed by: 

 

___________  ________________________  _____________________________ 

 

Serial Number 

Name 

 

 

 

Signature   

 

 

Date 

 

This Quick Tip is only a guide, always refer to your Operators Manual

 

FIGURE 3: 

Check filter 

FIGURE 2: 

Variable Speed Pulley 

FIGURE 1: 

Front Hood Removed 

Summary of Contents for T3100


























Reviews: