18
Detaching the machine
1.
Choose a place for detaching the machine. This needs to be a paved underground.
2.
Place a sideways roll able support under the front of the sod harvester and put down
the machine on this (this makes it easier to attach the machine).
3.
Put the trailer on a flat underground.
4.
Switch off the electric – and hydraulic system of the machine.
5.
Stop the engine of the tractor und put it on the handbrake.
6.
Put of the chain (nr. 8) from the hook of the lifting arm (nr. 10). To do this, don’t stand
in-between the machine and the tractor, but on the outside of the machine.
7.
Release the D-shutter from the connection point on the tractor (nr. 9) and slide the bar
(nr.7) from its connection point.
8.
Open the door of the trailer (nr. 1) from the backside.
9.
Release the different cables between the machine and the tractor with the connectors.
Put the cables and the fine-tuning of the main conveyor belts (nr. 6) backwards over
the trailer. This avoids that the cables come between the machine and the tractor.
10.
If the machine is equipped with an auto steer system disconnects the two hydraulic
tubes from the quick couplers of the tractor.
11.
Release the top link of the tractor from its upper connection point (nr. 4) with the
trailer.
12.
Release the lock washer from the hydro pump (nr. 5) en slides it from the p.t.o.-shaft.
Put the pump backwards over the trailer. This avoids that the cables come between the
machine and the tractor.
13.
Release the lock washer from the lower two connection points from the trailer (nr. 3)
and slide off the two connecting rings from the tractor from its connection points.
14.
Start the tractor and drive it straight out.
Attaching the machine
1.
Put the hydro pump (nr.5), fine-tuning speed main conveyer belts (nr. 6) and the
electric cables backwards over the trailer. This avoids that the cables come between
the machine and the tractor while attaching the machine. If the machine is equipped
with an auto steer system, you also need to put the hydraulic tubes backwards over the
trailer.
2.
Hang chain (nr. 8) over the machine.
3.
Open the door of the trailer from the backside.
4.
Drive the tractor as far backwards (over bar nr.7) that the lower pull bar off the tractor
is leaded into Center plate of the trailer.
5.
Watch out that nobody is in-between the trailer and the tractor! Connection of the
diverse parts of the trailer only through the opened door from the backside.
6.
Bring the two connection eyes from the lifting system of the tractor in the right height
for connection of the two lower connecting points of the trailer (nr. 3).
7.
Drive the tractor as far backwards that the two connection eyes from the lifting system
of the tractor can be slide on the two connection points of the trailer (nr. 3). Lock the
connection with the two lock clips.
8.
Switch of the hydraulic - and electric system of the sod harvester, turn off the engine
of the tractor, put it on the handbrake and take out the key from the contact.
9.
Slide the hydro pump (nr. 5) on the p.t.o. shaft en make sure this is correctly locked.
Locking is dependent on the type of tractor.
10.
Connect the top link of the tractor to the upper connection point (nr. 4) of the trailer.
Summary of Contents for Turf Tick
