manualshive.com logo in svg

turck TBEN-S2-4IOL, Instructions For Use Manual, Page: 91 / 134

Share
Download
turck TBEN-S2-4IOL Instructions For Use Manual Download Page 91

V01.00 | 2019/10

91

Error code

Designation acc. to specification

Meaning

0x8020

SERV_NOTAVAIL

The service is temporarily not available.

0x8021

SERV_NOTAVAIL_LOCCTRL

Service temporarily not available, device is
busy (e. g. teaching or parameterization of the
device at the device active)

0x822

SERV_NOTAVAIL_DEVCTRL

Service temporarily not available, device is
busy (e. g. teaching or parameterization of the
device via DTM/PLC etc. active)

0x8023

IDX_NOT_WRITEABLE

Access denied, index cannot be written

0x8030

PAR_VALOUTOFRNG

Parameter value out of the valid range

0x8031

PAR_VALGTLIM

Parameter value above the upper limit

0x8032

PAR_VALLTLIM

Parameter value value below the lower limit

0x8033

VAL_LENOVRRUN

Length of data to be written does not match
the length defined for this parameter

0x8034

VAL_LENUNDRUN

0x8035

FUNC_NOTAVAIL

Function not available in the device

0x8036

FUNC_UNAVAILTEMP

Function temporarily unavailable in the device

0x8040

PARA_SETINVALID

Invalid parameter: Parameters not consistent
with other parameters in the device.

0x8041

PARA_SETINCONSIST

Inconsistent parameters

0x8082

APP_DEVNOTRDY

Application not ready, device busy

0x8100

UNSPECIFIC

Vendor specific, according to device docu-
mentation

0x8101…
0x8FF

VENDOR_SPECIFIC

Summary of Contents for TBEN-S2-4IOL







































































































































Reviews:

No comments