![background image](http://html1.mh-extra.com/html/troy-bilt/ls-33-tb/ls-33-tb_operators-manual_1173099019.webp)
Adjustments
Wedge Assembly Adjustment
As normal wear occurs and there is excessive “play” between
the wedge and beam, adjust the bolts on the side of the wedge
assembly to eliminate excess space between the wedge and the
beam.
Loosen the jam nuts on the two adjustment bolts on the
1.
side of the wedge. See Fig. 6-2.
Turn the adjustment bolts in until snug and then back them
2.
off slowly (approximately 1-
1⁄2 turns).
Re-tighten the jam nuts securely against the side of the
3.
wedge to secure the adjustment bolts in this position.
Gib Adjustment
Periodically remove and replace the “gibs” (spacers) between the
wedge assembly and the back plate.
NOTE:
The gibs may be rotated and/or turned over for even wear.
Loosen the lock nuts under each back plate and slide the
1.
gibs out. See Fig. 6-2.
Rotate or replace the gibs.
2.
Re-assemble the back plate and secure with the lock nuts.
3.
Re-adjust the bolts on the side of the wedge assembly.
4.
Raising and Lowering Beam
Place the log splitter on a firm, level surface.
1.
To raise the beam for vertical operation:
2.
Pull out the horizontal beam lock on the tongue.
a.
Pivot beam lock down to release the beam.
b.
Move the beam to the vertical position. Secure it
c.
with the beam lock on the reservoir tank assembly.
WARNING!
Always use the log splitter in the
vertical position when splitting heavy logs.
Adjustment Bolts
Jam Nuts
Wedge
Gibs
Back Plate
Lock Nut
Hex screw
To lower the beam for horizontal operation:
3.
Pull out the vertical beam lock on the reservoir tank.
a.
Pivot the beam lock down to release the beam.
b.
Carefully pull back on the beam and lower it to the
c.
horizontal position.
To lock the beam in the horizontal position, pull out
d.
on the horizontal beam lock and rotate it to secure
the beam.
Beam and Splitting Wedge
The wedge plate on the log splitter is designed so the gibs on
the side of the wedge plate can be removed and rotated and/
or turned over for even wear. Make certain to readjust the
adjustment bolts so the wedge moves freely, but no excess space
exists between the wedge plate and the beam.
Off-Season Storage
If the log splitter will not be used for more than 30 days, prepare
for storage as follows:
WARNING!
Never store machine with fuel in the
fuel tank inside of building where fumes may reach
an open flame or spark, or where ignition sources
are present such as hot water and space heaters,
furnaces, clothes dryers, stoves, electric motors, etc.
Clean the log splitter thoroughly.
1.
NOTE:
The use of a pressure washers or garden hose to
clean your log splitter is not recommended. They may
cause damage to bearings or the engine. The use of water
will result in shortened life and reduce serviceability.
Wipe the log splitter with an oiled rag to prevent rust,
2.
especially on the wedge and the beam.
Drain the fuel tank. Always drain the fuel into an approved
3.
container outdoors, away from an open flame. Be sure that
the engine is cool before draining the fuel. Do not smoke
while handling fuel.
Start the engine and let it run until the fuel lines and
4.
carburetor are empty.
Remove the spark plug. Holding a rag over the cylinder
5.
hole, pour approximately 1⁄2-ounce (approximately one
tablespoon) of engine oil into the cylinder and crank slowly
to distribute the oil.
Replace the spark plug.
6.
Do not store the gasoline from one season to another.
7.
Replace your gasoline can if it starts to rust. Rust and/or dirt
8.
in the gasoline will cause problems.
Store the log splitter in a clean, dry area. Do not store next
9.
to any corrosive materials, such as fertilizer.
NOTE:
If storing in an unventilated or metal storage shed,
be certain to rustproof the equipment by coating with a
light oil or silicone.
Figure 6-2
19
s
ectiOn
6 — M
aintenance
& a
djustMents
Summary of Contents for LS 33 TB
Page 46: ...Notas 8 22...
Page 47: ...23 Secci n 8 Notas...