background image

5

s

ectiOn

 2 — i

MpOrtant

 s

afe

 O

peratiOn

 p

ractices

Keep your work area clean. Immediately remove split wood 

13. 

around the machine so you do not stumble over it.
Do not change the engine governor settings or overspeed 

14. 

the engine. The governor controls the maximum safe 

operating speed of the engine.
Never move this machine while the engine is running.

15. 

This machine should not be towed on any street, highway 

16. 

or public road without checking the existing federal, 

state, or local vehicle requirements. Any licensing or 

modifications such as taillights, etc., needed to comply, is 

the sole responsibility of the purchaser. If a “Statement of 

Origin” is required in your state, see your local dealer.
Do not tow machine over 45 mph.

17. 

See Transporting the Log Splitter section in this manual for 

18. 

proper towing instructions once all federal, local, or state 

requirements are met. 

Maintenance and Storage

Stop the engine, disconnect the spark plug and ground 

1. 

it against the engine before cleaning, or inspecting the 

machine.
Stop the engine and relieve hydraulic system pressure by 

2. 

cycling the valve control lever from forward to reverse 

several times while engine is not running; returning to 

neutral before repairing or adjusting fittings, hoses, tubing, 

or other system components.
To prevent fires, clean debris and chaff from the engine 

3. 

and muffler areas. If the engine is equipped with a spark 

arrester muffler, clean and inspect it regularly according to 

manufacturers instructions. Replace if damaged.

Periodically check that all nuts and bolts, hose clamps, and 

4. 

hydraulic fittings are tight to be sure equipment is in safe 

working condition.
Check all safety guards and shields to be sure they are in 

5. 

the proper position. Never operate with safety guards, 

shields, or other protective features removed.
The pressure relief valve is preset at the factory. Do not 

6. 

adjust the valve.
Never attempt to move this machine over hilly or uneven 

7. 

terrain without a tow vehicle or adequate help.
For your safety, replace all damaged or worn parts 

8. 

immediately with original equipment manufacturer’s 

(O.E.M.) parts only. “Use of parts which do not meet the 

original equipment specifications may lead to improper 

performance and compromise safety!”
Do not alter this machine in any manner, alterations such 

9. 

as attaching a rope or extension to the control handle, or 

adding to the width or height of the wedge may result in 

personal injury.

According to the Consumer Products Safety Commission 

10. 

(CPSC) and the U.S. Environmental Protection Agency (EPA), 

this product has an 

Average Useful Life

 of seven (7) years, 

or 130 hours of operation. At the end of the 

Average Useful 

Life

 have the machine inspected annually by an authorized 

service dealer to ensure that all mechanical and safety 

systems are working properly and not worn excessively. 

Failure to do so can result in accidents, injuries or death.

Spark Arrestor

WARNING: 

This machine is equipped with an 

internal combustion engine and should not be used 

on or near any unimproved forest-covered, brush 

covered or grass-covered land unless the engine’s 

exhaust system is equipped with a spark arrester 

meeting applicable local or state laws (if any).
If a spark arrester is used, it should be maintained in 

effective working order by the operator. In the State of California 

the above is required by law (Section 4442 of the California 

Public Resources Code). Other states may have similar laws. 

Federal laws apply on federal lands. 

A spark arrester for the muffler is available through your 

nearest engine authorized service dealer or contact the service 

department, P.O. Box 361131 Cleveland, Ohio 44136-0019.

Summary of Contents for LS 33 TB

















































Reviews: