background image

3

EN

oil heater IDX 30 D

Warning of flammable substances

Handling fuels entails a risk of fire.
Take sufficient precautions when handling fuels such
as fuel oil, kerosene or diesel.
Do not spill any diesel, kerosene or fuel oil! Do not
inhale the vapours nor swallow any fuel! Avoid skin
contact!

Warning of hot surface

Parts of the device, especially at the air outlet, become
very hot during operation. There is a danger of burning
and fire. Do not touch the device during operation!
During operation observe a safety distance of at least 
3 m to the device front! Observe the minimum distance
from walls or other objects according to the technical
data!

Warning of hot surface

Some parts of this product can become very hot and
cause burns. Particular attention has to be given where
children and vulnerable people are present!

Warning of hot surface

Improper handling entails a risk of burning. Only use
the device as intended!

Warning

Improper handling entails a risk of burning and electric
shock.
Only use the device as intended!

Warning

Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!

Warning

The device is not a toy and does not belong in the
hands of children.

Warning

Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.

Warning

Improper installation entails a risk of fire.
Do not place the device on combustible ground.
Do not place the device on high-pile carpets.

Warning

The device must not be covered, there is an imminent
fire hazard!

Behaviour in the event of an emergency

1. In case of an emergency, immediately extinguish the pilot

flame by actuating the on/off switch (position 

0

).

2. In an emergency, disconnect the device from the mains

feed-in: Switch the device off and disconnect it from the
mains.

3. Remove persons from the danger area.
4. Do not reconnect a defective device to the mains.

Overheating protection

The device is provided with a safety thermostat which is
activated by overheating of the device (when exceeding the
operating temperature).
Investigate the cause of overheating.
If the safety thermostat does not switch in the event of
overheating, the overheating protection will be tripped. In that
case the device switches off completely. If so, please contact
the customer service to have the overheating protection
replaced.

Information about the device

Device description

The directly fired oil heater 

IDX 30 D

 serves the purpose of

heating the room air so as to quickly heat large, well-ventilated
rooms. The oil heater runs on EL fuel oil, kerosene or diesel, it
must not be used with petrol, heavy fuel oil etc.
It is an oil heater with direct combustion to be installed in roofed
outdoor areas or in rooms with a sufficient fresh air supply.

Functional principle

The device generates warmth by conveying the sucked-in, cold
air past a combustion chamber. Inside the combustion chamber
the fuel is burned. The sucked-in air is heated and fed back to
the environment via the air outlet.
A part of the sucked-in air is compressed and conducted to the
injection. The fuel is fed from the tank to the injection by the
negative pressure thus created. An ignition contact at the
injection ignites the fuel, which is then burned in a continuous
flame.

Summary of Contents for IDX 30 D























Reviews: