background image

 

Storm-OM-001 - 

  

 

 

 

Storm-OM-001 

10 

28 February 2020 

This document, including the information contained herein, is proprietary to Triotech Amusement Inc. 

When parts of the furnishing are able to be adjusted or manipulated by the user, such as 
a power-adjusted chair, instructions shall be provided regarding their use. An illustration 
is able to be used with a required instruction to clarify the intent but shall not replace the 
written instruction.  

Operating,  maintenance,  and  installation  instructions  shall  be  provided  for  each 
furnishing and shall be included in the shipping carton of each furnishing.  

The instructions shall include, at least the directions and information required to cover 
the  mechanical  and  electrical  limitations  of  a  furnishing  and  the  intended  installation, 
maintenance, operation, and use of the product.  

The installation instructions shall specify the hardware used to mount or secure the 
furnishing to the building structure, where applicable. The installation instructions shall 
specify the method of mounting clearly, including the type and number of fasteners, the 
mounting surface material and whether the fasteners are intended to rely on studs, 
anchors or other features of the building construction. 

2.3

 

Grounding Instructions 

This  product  must  be  grounded.  If  it  should  malfunction  or  break  down,  grounding 
provides a path of least resistance for electric current to reduce the risk of electric shock. 
This  product is  equipped with a cord having an equipment-grounding conductor and a 
grounding  plug.  The  plug  must  be  plugged  into  an  appropriate  outlet  that  is  properly 
installed and grounded in accordance with all local codes and ordinances.  

 

 

DANGER

: Improper connection of the equipment-grounding conductor 

can result in a risk of electric shock. Check with a qualified electrician or 
service  technician  if  you  are  in  doubt  as  to  whether  the  product  is 
properly grounded. Do not modify the plug provided with the product if 
it  will  not  fit  the  outlet;  have  a  proper  outlet  installed  by  a  qualified 
electrician. 

This product is for use on a multiple voltage circuit and requires grounding. Make sure 
that the product is connected to an outlet having the same configuration as the plug. No 
adapters should be used with this product. 

 

 

Summary of Contents for Storm VR









































































Reviews: