Triotech Storm VR Owner'S Manual Download Page 47 | Manualshive

Page: 47 / 72

background image

Maintenance and Repairs

Storm-OM-001

47

28 February 2020

This document, including the information contained herein, is proprietary to Triotech Amusement Inc.

10.5

Replacing a speaker

Gain access to the front cabinet by removing the front and top plate of the cabinet.

•

Disconnect the speaker cable.

•

Remove the screws holding the speaker.

•

The speaker can now be removed and replaced.

Before starting any maintenance operation, make sure that the power has

been disconnected for at least 1 minute.

«
...
45
46
47
48
49
...
»

Summary of Contents for Storm VR









































































Reviews:

No comments

Related manuals for Storm VR

Brand: NAMCO Pages: 44

Brand: LAI Games Pages: 43

Brand: Samsung Pages: 92

Brand: UNIS Pages: 51

Brand: Atari Pages: 89

Lane Master Pro

Brand: UNIS Pages: 40

Brand: UNIS Pages: 37

Brand: Vendo Pages: 46

Brand: Crane Pages: 46

Brand: Automaten Hoffmann Pages: 8

Brand: MONSTER MOBILE Pages: 13

Brand: Bay-Tek Pages: 2

SKEE BALL MARQUEE

Brand: Bay-Tek Pages: 21

Brand: Bay-Tek Pages: 24

Brand: Bay-Tek Pages: 40

Brand: Bay-Tek Pages: 43

Brand: Bay-Tek Pages: 50

Lil Ticket Monster

Brand: Bay-Tek Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands