Trinity Highway QuadGuard Elite M10 Product Description Assembly Manual Download Page 8

Page: 8 / 60

TrinityHighway.com

Revision C September 2021

System Assemblies

System assemblies that may be ordered in your particular QuadGuard

Elite M10 configuration.

Verify parts delivered and system details with the BOM (Bill of Materials) and system drawings
shipped with your system. Please call Trinity Highway if you have any system questions (p. 3).

Note:

Parts and

Assemblies are not shown to scale.

Monorail Assembly – 611354 (3540060-0800)

Item

EAS PN

Description

Qty

611379

2760071-0000

Monorail, 3 Bay

611370

2760051-0000

Monorail, 1 Bays

608136

2760041-0000

Endcap, Monorail

619316

Anchor Kit, Hilti, 330 ml, 3/4x7 (4)

113660

2699571-0000

Bolt, Hex, 5/8x3 1/2, G5

118100

2708231-0000

Washer, Lock, 5/8

003354

2704141-0000

Nut, Heavy Hex, 5/8, A563

Summary of Contents for QuadGuard Elite M10





























































Search results

Summary of Contents for QuadGuard Elite M10

Reviews:

Related manuals for QuadGuard Elite M10

Brands by name

Popular brands

Trinity Highway QuadGuard Elite M10, Product Description Assembly Manual

Search results

Summary of Contents for QuadGuard Elite M10

Reviews:

Related manuals for QuadGuard Elite M10

Brands by name

Popular brands