Trine 4100 Electric Strike Installation Instructions Manual Download Page 56

Page: 56 / 65

W I R E L E S S C H I M E 2 3 2

1440 Ferris Place Bronx NY 10462
Tel: 718-829-2332

Fax: 718-829-6405

web-site: www.trineonline.com
E-mail: [email protected]

Install alkaline type A23 12 volt push button

battery.

Remove back of case by pushing in tab

on bottom with a small screwdriver. Make sure
battery is oriented properly.

Mount push button and chime.

Test Range.

Temporarily position chime

and push button where you want them
mounted. Press push button to verify
chime and push button work properly. If
chime does not sound, see Troubleshooting.

Open chime case.

Press in catch on
bottom of chime and lift
the case open.

Install 2 alkaline “C”

batteries.

Make sure

batteries are oriented
properly.

Use either screws or double sided tape to mount
push button.
To mount with scrws, remove back of case by push-
ing in tab on bottom with a small screwdriver.
Attach back of case to door jamb or wall. Snap
front of push button on.
When attaching push button using double sided
tape, make sure the surface of the door jamb or wall
is clear.
Position button with label “Install This End Down”.
Case Style: Chime can be mounted by using 1
screw with keyhole.
Snap battery access door firmly in place before
mounting.

Code and Tune Settings

Code Settings

Note:

Most installations will not require you to change any jumpers

on your chime and push button.

The push button and chime communicate by using a code that can be
changed by removing and/or adding jumpers on both the push button and
chime. The code is factory set; however, there are 128 selectable codes
that allow you to expand your system and prevent outside interference.
Other wireless products may cause interference and the system may not
function properly. Follow the instructions below for setting a new code.

1. Open the cases and locate the jumpers on both the push button and

chime.

2. The push button and chime both have eight different jumper locations.

The jumper positions 1 thru 7 are used for setting the code.

3. To change the code, add and/or remove jumpers as needed.

It is

recommended to only change one jumper at a time and then
check to see if system is functioning properly

. Note: Jumpers in

positions 1 thru 7 must be exactly the same for both the push button

and chime for this system to function.

Troubleshooting

Chime doesn’t sound:

Make sure push button and chime codes are the same
Check orientation of push button battery
Check charge of push button and chime batteries, replace if

necessary.

Batteries seem OK, but the chime doesn’t work when

installed:

Don’t mount chime or push button on metal or near metal

studs. This reduces the transmitter range. Use 1/4” to 1/2”
(6 to 13 mm) wood shims to move chime or push button off
metal surface.

Concrete floors may reduce range. Move chime away from

floor.
Try locating chime closer to push button.

The range of the wireless chime can vary with location, tempera-
ture and battery condition.

Regulartory Information

This device complies with Part 15 of the FCC Rules and RSS-20
of Industry Canada. Operation is subject to the following condi-
tions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
The user is cautioned that changes or modifications not express-
ly approved by the party responsible for regulatory compliance
could void the user’s authority to operate equipment

FCC, IC RECOGNIZED

ONE YEAR LIMITED WARRANTY

Push Button Battery Replacement

Install an alkaline type A23 12 Volt battery The
positive terminal should be positioned as shown.

*Code Settings 1-7

Must Match Both
Push Button and

Chime

Tune Setting

Inside Chime

Inside

Push Button

Tune Setting

(Not used on

all models)

Note: Some models might

require the use of tweezers to

remove and replace the jumpers

REV53002

TRINE ACCESS TECHNOLOGY reserves the right to discontin-
ue and to change specifications at any time without notice incur-
ring any obligation to incorporate new reatures in previously sold
products.

This package includes (Style of push button and chime may vary from
illustration):

Wireless chime

Wireless push button w/battery

Mounting hardware pack

You’ll need to buy 2 “C” alkaline batteries for the chime. In typical use
alkaline batteries will last up to one year.

Tune Setting

Your wireless chime has two different selectable tunes:

Ding

(One note),

Ding-Dong

(two note). The factory setting is for the

Ding-Dong tune. This tune can be changed by following the
instructions below: