Trine 4100 Electric Strike, Installation Instructions Manual

Page: 52 / 65

206-3 -- Wireless
Entry/Exit Signal Kit
Instruction Sheet
Trou bleshooting
PHONE: (203) 730-1756
FAX: (203) 730-1781
2 PARKLAWN DR. STE F, BETHEL, CT 06801
customerservice@trineonline.com
www.trineonline.com
NOTE: This unit is NOT compatible with 206-3
units sold before
December, 2014
For swingin g doors
align the tran smitter
arr ow t o the bottom
of the magn et
as sho wn.
V. 16.0504
• Transmitter
communicates with the
chime wirelessly.
• Can be used with swinging
or sliding doors
• Chime plugs into a
standard electric outlet
• Includes a Door Magnet
Spacer and all the
mounting screws
• Transmitter range: 100’
• Three High Quality Chime
tunes
• (1) 12V A23 Battery is
included
A. Pr oblem
: Chime does not rin g one time
and st op.
1a. P ossible Cause: Sen sor ba tter y is not
installed pr oper ly.
1b. Fix: Make sur e batter y is insta lled
accor ding t o the diagra m inside sen sor.
2a. P ossible Cause: Sen sor ba tter y is dead.
2b. Fix: R eplace sensor b atter y.
3a. P ossible Cause: Chime is n ot receivin g
pow er
3b. Fix: Ma ke sur e the plug-in c hime has
pow er
4a. P ossible Cause: Sen sor & Chime a re no t
synced
4b. Fix: R e-try syn cing pr ocess
- Unplug c hime
- Ensur e switc h 1 on both c hime and
sensor is set t o OFF
- Wait 30 Secon ds
- Press and hold the “ TEST” button
inside the sen sor within 20 secon ds after
plugging in chime. When the “Din g-dong”
tune is pla yed, the sen sor is syn ced with
the chime.
B. Problem
: Batter y seems okay bu t the chime
does not w ork af ter in stallation.
1a. P ossible Cause: Chime or Tran smitter is
mounted on meta l or nea r me tal stud s.
(meta l redu ces ran ge of unit)
1b. Fix: Use a 1/4” to 1/2” w ooden shim t o to
move Tra nsmitt er a way fr om meta l surfa ce.
Move Chime t o another wall outle t.
2a. P ossible Cause: Chime or Tran smitter is
mounted n ear con cret e. (concr ete r educes
range of u nit)
2b. Fix: Mo ve a way fr om concret e
3a. P ossible Cause: Chime & T ransmitt er ar e
installed t oo far a part (o ver 100 f eet)
3b. Fix: reloca te pieces closer to on e ano ther.
C. Problem
: Chime sounds when not in ten ded.
1. P ossible Cause: Chime or Tra nsmitter is
receivin g inter fer ence
2. Fix: Follo w A. Pr oblem - 4b. Fix to Un sync the
unit
- Follo w A. Pr oblem - 4b. Fix A gain to
Resyn c the units
- If prob lem persists mo ve Chime or
Tran smitter t o ano ther loca tion to red uce
inter fer ence.
FEATURES:
NOTE: This u nit is NO T
compatible with 206-3
units sold before
December , 2014
What’s Included:
Installation:
Chime
(Plug in)
**Note: Arrows do not line up**
**Position as shown**
Door
Magnet
Door
Magnet
Wireless
Transmitter
Spacer
Mounting
Screws
Chime Selection Chart
Transmitter
& Trigger
Screws
Magnet
Spacer
Magnet
Spacer
1. Plug the chime on an electric outlet within the
range of the transmitter. It will take 30 seconds for
the electronics to initialize.
2. Take off the back cover of the transmitter unit to
find the programming switches.
3. After the chime initializes, push the “Test Button”
on the transmitter for 20 seconds so the chime can
pair with the transmitter.
Note:
A “Ding-Dong” sound from the chime indicates that
the transmitter has been successfully mated with the
chime.
A single “Ding” from the chime indicates that the
transmitter memory was erased.
4. Select the desired chime sound. See the selection
chart for the dip switch combinations.
5. Mount the transmitter unit on to the door frame.
6. ** Align the door magnet with the transmitter -
see door positioning above** Use the door magnet
spacer if the door is recessed too far from the frame.
7. Test the completed installation. Refer to the trou-
bleshooting section if the installation does not work.
Transmitter
Chime
Test
Button
Transmitter
Dip Switch
Transmitter
Switch 2 - ON
Switch 2 - OFF
Switch 2 - OFF
Switch 2 - ON
Tune
Ding
Ding-Dong
Ding-Dong
Westminster
Chime
Switch 2 - ON
Switch 2 - OFF
Switch 2 - OFF
Switch 2 - ON