Trillium 10-WSP Installation, Operation & Maintenance Instructions Manual Download Page 7

Page: 7 / 72

WSP™

DATA SHEET

WSP™ SELF-PRIMER PUMPS

WSP-D300_10

Rev. 3

01/09/20

WHEN PERFORMING EQUIPMENT MAINTENANCE OR IF THE PUMP IS TO

REMAIN OUT OF SERVICE FOR A PERIOD OF TIME, THE EQUIPMENT

ELECTRICAL SERVICE MUST BE DISCONNECTED WITH AN APPROVED

LOCKOUT AND KEY. FAILURE TO LOCK OUT THE EQUIPMENT MAY RESULT IN

INJURY.

IF OVERHEATED, THE PUMP MUST BE ALLOWED TO COMPLETELY

COOL BEFORE ATTEMPTING ANY PROCEDURES.

2. CHECK THE TEMPERATURE BEFORE OPENING ANY COVERS,

PLATES, OR PLUGS.

3. ENSURE THAT SUCTION AND DISCHARGE VALVES ARE CLOSED.

4. SLOWLY AND CAREFULLY VENT THE PUMP.

5. DRAIN THE PUMP.

ONCE THE PUMP HAS BEEN POSITIONED, ENSURE THAT ALL PUMP AND PIPING

CONNECTIONS ARE TIGHTENED, SECURED, AND SUPPORTED PROPERLY.

ALL GUARDS AND PROTECTIVE DEVICES MUST BE INSTALLED BEFORE THE PUMP

IS STARTED. CONTACT WITH UNGUARDED BELTS, SHEAVES, OR COUPLINGS

COULD RESULT IN INJURY.

PLATES, COVERS, GAUGES, PIPE PLUGS, OR FITTINGS MUST NOT BE

REMOVED FROM AN OVERHEATED PUMP. VAPOR PRESSURE WITHIN THE

PUMP MAY CAUSE PARTS TO BECOME DISENGAGED AND EJECTED WITH

GREAT FORCE, CAUSING POTENTIAL SEVERE INJURY TO PERSONNEL.

ALWAYS ALLOW THE PUMP TO COOL BEFORE SERVICING ANY EQUIPMENT.

Summary of Contents for 10-WSP









































































Search results

Summary of Contents for 10-WSP

Reviews:

Trillium 10-WSP, Installation, Operation & Maintenance Instructions Manual, Page: 7 / 72

Search results

Summary of Contents for 10-WSP

Reviews: