Trillium 10-WSP Installation, Operation & Maintenance Instructions Manual Download Page 16

Page: 16 / 72

WSP™

DATA SHEET

WSP™ SELF-PRIMER PUMPS

WSP-D300_10

Rev. 3

01/09/20

IV. DISASSEMBLY & REASSEMBLY OF THE PUMP & SEAL

Review all warnings before performing installation and follow the directions on all

tags, labels, and decals attached to the pump very closely.

Your pump requires minimum service due to its rugged, low maintenance design.

Should you need to inspect or replace wearing parts, follow these instructions. They

match the sectional views and the list of appropriate parts.

Instructions in this manual are intended to inform the operator about any procedures

that need extra attention. It will also make note of procedures that could damage

equipment or cause danger to the operator and/or other employees. This manual

will

not

anticipate or provide in-depth precautions for every possible situation that

could happen during maintenance or repair of the WSP™ Self-Primer Pump. As

always, it is the owner’s and maintenance staff’s duty to be sure that safety and

established maintenance procedures and processes are used. Any procedures or

processes

not

noted in this manual should only be completed

after

determining that

personal safety and equipment integrity is not harmed.

A number of servicing functions may be completed by draining all the liquid from the

pump and removing the cover plate assembly. Before making significant repairs,

disconnect the power source and piping. The following instructions require complete

disassembly.

Before disassembly, determine the material type and configuration of the pump if

unknown. The first set of characters in the pump name describes the size and model

of the pump (10-WSP is a 10” self-primer). Use the following key to determine the

materials used in the pump from the remaining characters in the pump name.

THIS SPACE INTENTIONALLY LEFT BLANK

Summary of Contents for 10-WSP









































































Search results

Summary of Contents for 10-WSP

Reviews:

Trillium 10-WSP, Installation, Operation & Maintenance Instructions Manual, Page: 16 / 72

Search results

Summary of Contents for 10-WSP

Reviews: