Trillium 10-WSP Installation, Operation & Maintenance Instructions Manual Download Page 11

Page: 11 / 72

WSP™

DATA SHEET

WSP™ SELF-PRIMER PUMPS

WSP-D300_10

Rev. 3

01/09/20

SERIOUS DAMAGE COULD OCCUR TO THE PUMP ASSEMBLY IF BOTH LIFTING EYES

ARE NOT UTILIZED DURING LIFTING AND MOVEMENT OF THE UNIT. ONLY LIFT THE

PUMP WITH THE LIFTING EYES.

IN HIGH DISCHARGE HEAD APPLICATIONS THE DISCHARGE THROTTLING VALVE

MUST BE GRADUALLY CLOSED BEFORE THE PUMP IS STOPPED.

BYPASS LINES MUST BE SECURED AGAINST BEING DRAWN INTO THE PUMP

SUCTION INLET WHEN RETURNED TO A WET WELL.

ALIGNMENT ADJUSTMENT IN ONE DIRECTION MAY DISRUPT ALIGNMENT

ADJUSTMENT IN ANOTHER DIRECTION. CHECK EACH PROCEDURE AFTER

ALTERING ALIGNMENT.

PUMP PERFORMANCE INCLUDING SPEED AND OPERATING CONDITIONS ARE

REQUIRED TO BE WITHIN THE RANGE SHOWN ON THE MANUFACTURER’S PUMP

PERFORMANCE CURVE.

THIS PUMP SHOULD ALWAYS BE OPERATED WITH LIQUID IN THE PUMP CASING.

WHEN OPERATING THE PUMP DRY, THE PUMP WILL NOT PRIME.

Summary of Contents for 10-WSP









































































Search results

Summary of Contents for 10-WSP

Reviews:

Trillium 10-WSP, Installation, Operation & Maintenance Instructions Manual, Page: 11 / 72

Search results

Summary of Contents for 10-WSP

Reviews: