manualshive.com logo in svg

Trillium 10-WSP, Installation, Operation & Maintenance Instructions Manual, Page: 20 / 72

Share
Download
Trillium 10-WSP Installation, Operation & Maintenance Instructions Manual Download Page 20

WSP™ 

DATA SHEET

 

WSP™ SELF-PRIMER PUMPS 

WSP-D300_10 

Rev. 3 

 

01/09/20 

 

 

© 2019 The Factory 

20 

 

Figure 2 

 

C.  REMOVING THE ROTATING ASSEMBLY  

 

To maintain the rotating assembly without disconnecting the suction or discharge 

piping, go through the rear of the pump.  You may also service the rotating assembly 

from the front of the pump by taking off the suction inlet, or “goose neck.” 

 

While being sure the suction inlet assembly is supported, take out the mounting 

hardware, the suction inlet assembly and the suction inlet gasket. 

 

There are two sets of 16mm taped holes in the front wearplate to facilitate its 

removal (top, bottom and at 120° increments).  The holes are not completely taped 

so they must be used with a puller. 

 

Examine the front wearplate and its gasket, and install new ones if they appear worn 

or damaged.  

 

To prevent seal cavity oil from escaping when the impeller is loosened, remove the 

seal cavity drain plug, and drain the oil in the seal cavity before loosening the 

impeller. 

 

With the rotating assembly still attached to the pump casing, loosen the impeller.  

When done, clean, inspect and reinstall the drain plug in the seal cavity. 

 

Remove the inner circle of bolts from the retainer plate and move them to pusher 

holes.  Evenly tighten the bolts to push the entire rotating assembly toward the 

suction.  Once the impeller is through the casing a strap of adequate strength (1 ton 

Summary of Contents for 10-WSP









































































Reviews:

No comments