Trillium 10-WSP Installation, Operation & Maintenance Instructions Manual Download Page 3

Page: 3 / 72

WSP™

DATA SHEET

WSP™ SELF-PRIMER PUMPS

WSP-D300_10

Rev. 2

11/7/19

5. Suction Line Positioning ............................................................................ 45

F. DISCHARGE LINES .................................................................................. 46

1. Siphoning ................................................................................................... 46

2. Valves ........................................................................................................ 46

3. Bypass Lines ............................................................................................. 47

G. WSP™ AUTOMATIC AIR RELEASE VALVE (WSP™ ARV) .................... 48

1. Theory of Operation ................................................................................... 49

2. WSP™ Air Release Valve Installation ....................................................... 50

H. ALIGNMENT .............................................................................................. 52

1. Coupled Drives .......................................................................................... 53

2. Spider Insert-type Couplings ..................................................................... 53

3. Non-Spider Type Couplings ....................................................................... 53

4. V-Belt Drives .............................................................................................. 54

IX.

OPERATION ................................................................................................. 54

A. Priming ...................................................................................................... 55

B. START-UP ................................................................................................. 56

1. Rotation ..................................................................................................... 56

C. OPERATION ............................................................................................. 56

1. Lines with a Bypass ................................................................................... 56

2. Lines Without a Bypass ............................................................................. 57

3. Leaking ...................................................................................................... 57

4. Liquid Temperature and Overheating ........................................................ 57

5. Strainer Check ........................................................................................... 58

6. Checking the Pump Vacuum ..................................................................... 58

D. STOPPING ................................................................................................ 59

1. General Information for Pump Storage ...................................................... 59

2. Preserving the Pump in Cold Weather ...................................................... 60

E. CHECKING THE BEARING TEMPERATURE .......................................... 60

TECHNICAL DATA ....................................................................................... 62

A. 10” WSP Curve .......................................................................................... 62

B. 10” WSP General Arrangement Drawing ................................................... 63

C. 10” WSP Sectional Drawing and Parts List................................................ 63

D. WSP™ Air Release Valve Drawing and Parts List .................................... 71

Summary of Contents for 10-WSP









































































Search results

Summary of Contents for 10-WSP

Reviews:

Trillium 10-WSP, Installation, Operation & Maintenance Instructions Manual, Page: 3 / 72

Search results

Summary of Contents for 10-WSP

Reviews: