background image

 

 

 

 

 

Trienergia S.r.l.

 

 Strada Pavesa, 13/A   
 Bondeno di Gonzaga  
 (MN) 46023  
 Italy  
 
 VAT No. 02470010204 
 
 

www.trienergia.it

  

 

[email protected]

  

 +39 (0)376 595052 

 

12 

 

 

            Maintenance and inspections 

Service and maintenance on the TRIxxxBC-xB photovoltaic modules must only be 
carried out  by qualified personnel. Do not  clean the glass surface with alkaline 
detergents. Avoid prolonged stagnation of water on the glass. Be careful not to 
break  or  damage  the  grounding  wire  during  routine  maintenance  of  the 
photovoltaic module. 

It  is  recommended  to  perform  the  following  maintenance  and  inspection 
procedures regularly: 

 

Cleaning of glass surfaces; 

 

Snow removal, if necessary; 

 

Visual inspection of the fixing system; 

 

Visual inspection of photovoltaic modules; 

 

Visual inspection of electrical connections; 

 

Performance verification. 

 

             

               Disposal 

For  any  questions  regarding  the  disposal  or  recycling  of  the  TRIxxxBC-xB 
photovoltaic modules contact Trienergia using the contact details in the header

 

 

 

 

 

 

 

 

 

Summary of Contents for TRIxxxBC-xB Series













Reviews: