manualshive.com logo in svg

Trident TRIDENT 1U1I, User Manual

Share
Download
Trident TRIDENT 1U1I User Manual Download Page 12

 

GU_TRIDENT_V_1_20_EN

 

12/47 

 

The following screen appears  : 

 

        C O N  F  I  G  .    C O M  .         

S  p  e  e  d        :    9  6  0  0  B  a  u  d  s   

A  d  d  r  e  s  s    :    0  0  1               

P  o  r  t          :    R  S  2  3  2           

 

 

Speed

.   The communication speed can be modified using the + and - keys. Possible values: 1200, 

2400, 4800 or 9600 bauds.  

 

Address

.  The  address  of  TRIDENT  can  vary  from  1  to  255  and  must  be  identical  to  that 

programmed  in  WINTRID.  This  address  system  enables  communication  with  several  
TRIDENTs  connected  on  the  same  network  (type  RS485,  for  example).  Only  the  one 
with the corresponding address will respond. 

 

Port

.  

The communication protocol cannot be modified (RS232 standard, RS485 on request). 

 

Confirm the various fields. The correct operation of the communication with WINTRID can then be 
checked, see the WINTRID documentation to carry out this test. 
 

The  green  lamp 

communication

  lights  each  time  the  device  receives  a  correct  information 

packet  intended  for  it. 

This  enables  simple  verification  of  the  communication  and  is  a 

troubleshooting aid. 

 
 

If there is a communication failure, check: 
 

 

That  TRIDENT  is  properly  connected  to  the  correct  PC  port  with  the  cable  provided  with 
TRIDENT, 

 

That the communication parameters are all identical, 

 

That TRIDENT is supplied by an external supply (TRIDENT does not communicate when it is 
powered by its back-up battery). 

 

Note

 : The communication is 8 bits, no parity, with a start bit and a stop bit. 

 

Summary of Contents for TRIDENT 1U1I

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands