manualshive.com logo in svg

TriangleTube Prestige Slol 250, Installation And Maintenance Manual

Share
Download
TriangleTube Prestige Slol 250 Installation And Maintenance Manual Download Page 85

78

Product Specifications

Output
Note 4

157,500

94.1%

95.1%

Fuel

Combustion

Efficiency

Input

Note 4

Output
Note 4
Note 5

Thermal

Efficiency

Net IBR

Rating
Note 2

Shipping

Weight

Lbs / Kg

Boiler

Model

225,500

379,000

399,000

330,000

225 / 102

Natural

SOLO 399

102,500

110,000

102,500

Propane

87,000

Fuel

DOE

Heating Capacity

Note 1 & 4

Input

Note 4

DOE Seasonal

Efficiency AFUE

Note 3

Net IBR

Rating
Note 2

60,000

95%

Shipping

Weight

Lbs / Kg

95 / 43

Natural

Boiler

Model

SOLO 60

47,000

110,000

102,500

95%

95 / 43

Propane

87,000

154,000

54,000

170,000

95%

131 / 60

Natural

SOLO 175

134,000

102,500

102,500

95%

131 / 60

Propane

Propane

87,000

223,000

245,000

95%

142 / 65

Natural

SOLO 250

194,000

102,500

110,000

102,500

95%

142 / 65

87,000

Note 1:

The heating capacity of the PRESTIGE Solo
60/175/250 is based on the test requirements
of the U.S. Department of Energy.

Note 2:

The IBR rating is based on a piping and pick
up allowance of 1.15. This allowance should
be sufficient for the standard radiation
requirements for a building load.

Note 3:

Based on the given AFUE the PRESTIGE
Solo 60/175/250 meets the energy efficiency
guidelines established by Energy Star.

Note 4:

Input and output ratings are shown for sea
level applications. The PRESTIGE Solo
automatically derates the input at approxi-
mately 2% for every 1,000 Ft. of altitude. No
alterations to the boiler or burner system is
required.

Note 5:

PRESTIGE Solo 399 output rating is based
off of the thermal  efficiency.

DOE

Summary of Contents for Prestige Slol 250


























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands