manualshive.com logo in svg

TriangleTube Prestige Slol 250, Installation And Maintenance Manual

Share
Download
TriangleTube Prestige Slol 250 Installation And Maintenance Manual Download Page 15

9

Combustion Air and Venting

Outdoor Opening(s) Location.  Outdoor open-
ing(s) shall be located in accordance with the
Outdoor Combustion Air section.

Outdoor Opening(s) Size.  Outdoor opening(s) shall
be calculated in accordance with the following:  

-

The ratio of the interior spaces shall be
the available volume of all communi-
cating spaces divided by the required
volume.

-

The outdoor size reduction factor shall
be 1 minus the ratio of interior spaces.

-

The minimum size of outdoor open-
ing(s) calculated in accordance with the
above outdoor air section multiplied by
the reduction factor.

The minimum

dimension of air openings shall not be
less than 3 in.

Do not install the PRESTIGE Solo  into a

common vent with other gas or oil appli-

ances.  This may cause flue gas spillage or

appliance malfunction, resulting in possi-

ble severe personal injury, death or sub-

stantial property damage.

Combustion Air and Vent Piping

The PRESTIGE Solo requires a Category IV
venting system, which is designed for pressur-
ized venting and condensate.

The PRESTIGE Solo is certified per ANSI
Z21.13 as a Category IV or Direct Vent (sealed
combustion) appliance. A Category IV appli-
ance utilizes uncontamined indoor or outdoor
air (surrounding the appliance) for combustion.
A Direct Vent appliance utilizes uncontaminat-
ed outdoor air (piped directly to the appliance)
for combustion.

In order to reduce the potential risks

associated with indoor contaminates

(listed on page 5), flammable vapors

and tight housing construction (little or

no infiltration air), it is recommended

to pipe uncontaminated combustion air

directly from the outdoors to the appli-

ance. This practice also promotes higher

system efficiency by reducing heated

indoor air from being exhausted from

the house and replaced by cold infiltra-

tion air into the house.

Install combustion air and vent pipe as

detailed in the PRESTIGE Solo Vent

Supplement included in the boiler

installation envelope. Refer to optional

vent kit instructions for addition vent

installation instructions.

Verify installed combustion air and vent

piping are sealed gas tight and meet all

provided instructions and applicable

codes, failure to comply will result in

severe personal injury of death.

DANGER

NOTICE

BEST PRACTICES

DANGER

Summary of Contents for Prestige Slol 250


























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands