manualshive.com logo in svg

TriangleTube Prestige Slol 250, Installation And Maintenance Manual

Share
Download
TriangleTube Prestige Slol 250 Installation And Maintenance Manual Download Page 58

52

Outdoor Reset Control

CH Reset Curve Warmest Day

(Parameter 12)

This parameter is not applicable if an outdoor
sensor is not connected to the boiler.  When an
outdoor temperature sensor is connected, the
CH Reset Curve Warmest Day is the warmest
design temperature of the heating system.

Entering MCBA Access Code

The installer must enter the MCBA Access
Code to adjust the advanced parameter settings
of the MCBA.  The Access Code can be
entered as follows:

1.  Press the MODE button until the display

shows 

STBY

.

2.  Press and hold the MODE and STEP but-

tons together for 2 to 3 seconds until the
display shows 

CODE

.

3.  Press the STEP button once and the display

will show 

C_

XX

where 

XX

represents a ran-

dom number.

4.  Press the “+” or “–“ buttons to change the

number displayed to read 

C_54

.

.  Press and

hold the “+” or “–“ button to rapidly
change the number.

5. When the display reads 

C_54

, press the

STORE button to save the Access Code.
The display should flash to indicate that the
Access Code was saved.

After the Access Code has been entered, the
advanced parameters can be accessed by press-
ing the MODE button until the display shows

PARA

.  Once the display shows 

PARA

, press

the STEP button to reach the appropriate para-
meter.  The display should follow the following
sequence:

Press STEP once-

1140

Press STEP x2 -

2_01

Press STEP x3 -

3_01

Press STEP x4 -

4186

Press STEP x5 -

P_10

Press STEP x6 -

P_11      

Etc......

After Parameter 4, the display will show P fol-
lowed by the parameter number.  Once a par-
ticular parameter is reached, the display will
change to show the current setting of that para-
meter.

The actual parameter values displayed on

the display may vary depending on the

application, but the sequence will always

occur in the order shown.

Changing a Parameter Setting

1.  Use the “+” or “–“ button to change the

parameter setting.

2.  Press the STORE button to save the

change.  The display should flash to indi-
cate that the change was saved.

3.  Press the RESET button to leave the Access

Code mode.

NOTICE

Summary of Contents for Prestige Slol 250


























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands