manualshive.com logo in svg

TriangleTube Prestige Slol 250, Installation And Maintenance Manual

Share
Download
TriangleTube Prestige Slol 250 Installation And Maintenance Manual Download Page 31

25

Installing Vent/ Combustion Air & Condensate Drain

SECTION V - Installing Vent /

Combustion Air & Condensate Drain

Installing Vent and Combustion Air

The PRESTIGE Solo must be vented

and supplied with combustion air as

shown in the PRESTIGE Solo Vent

Supplement,  included in the boiler

installation envelope. Refer to optional

vent kit instructions for additional vent

installation instructions.  Once installa-

tion is completed, inspect the vent and

combustion air system thoroughly to

ensure systems are airtight and comply

with the instructions given in the venting

supplement and are within all require-

ments of applicable codes.  Failure to

comply with the installation require-

ments on the venting and combustion air

piping will cause severe personal injury

or death.

Installing Condensate Drain Assembly

1.  Locate the condensate drain assembly and

install as shown in Fig. 15 page 26.

The installer may want to fill the con-

densate trap with water prior to assem-

bling on the unit.

2.   Remove the retaining nut and rubber seal

from the condensate drain assembly and
slide over the heat exchanger condensate
drain nipple. Connect the condensate drain
assembly to the retaining nut and tighten.

Hand tight only!

Ensure the condensate drain assembly

contains the plastic seated ball. Do not

install the condensate drain assembly if

the ball is lost or missing, replace the

entire assembly.

3.  Remove the compression nut and rubber

seal from the drain outlet.

4.   Using 3/4” x 2’ flexible PVC tube provid-

ed, slide the compression nut and rubber
seal over the pipe

The use of 3/4” PVC or CPVC pipe is

also acceptable. If 3/4” pipe is used

deburr and chamfer pipe to allow mat-

ing onto the drain assembly.

5.   Thread the rubber seal into the compres-

sion nut to ease installation of the pipe to
the drain assembly.

6.  Seat the pipe onto the drain assembly and

tighten the compression nut.  

Hand tight

only!

The installer may opt to using 13/16" ID

tubing in lieu of rigid piping.

The drain line materials must be an

approved material by the authority hav-

ing jurisdiction.  In absence of such

authority, PVC and CPVC piping must

comply with ASTM D1785 or D2845.

The cement and primer used on the pip-

ing must comply with ASME D2564 or

F493.  For installations in Canada, use

CSA or ULC certified PVC or CPVC

pipe, fittings and cement/primer.

7.  Continue the pipe from the drain assembly

to a floor drain or condensate pump.

NOTICE

NOTICE

NOTICE

WARNING

NOTICE

DANGER

Summary of Contents for Prestige Slol 250


























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands