manualshive.com logo in svg

TriangleTube Prestige Slol 250, Installation And Maintenance Manual

Share
Download
TriangleTube Prestige Slol 250 Installation And Maintenance Manual Download Page 8

2

Do not use this appliance if any part

has been under water. Immediately call

a qualified service technician to inspect

the appliance and to replace any part of

the control system which has been

under water.

WHAT TO DO IF YOU SMELL GAS

- Do not try to light any appliance
- Do not touch any electrical switch; do

not use any phone in your building.

- Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions.

- If you cannot reach your gas suppli-

er, call the fire department.

Installation and service must be per-

formed by a qualified installer, service

agency or the gas supplier.

Should overheating occur or the gas
supply fails to shut off, turn OFF the
manual gas control valve external to
the appliance.

DO NOT add cold make up water when
the boiler is hot. Thermal shock can
cause potential cracks in the heat
exchanger.

When servicing the boiler:
-

Avoid electrical shock by discon-
necting the electrical supply prior to
performing maintenance.

CAUTION

WARNING

WARNING

WARNING

DANGER

Product & Safety Information

Qualified Installer:

Prior to installing this product read all
instructions included in this manual and all
accompanying manuals/documents with this
appliance. Perform all installation steps
required in these manuals in the proper
order given. Failure to adhere to the guide-
lines within these manuals can result in
severe personal injury, death or substantial
property damage.

Homeowner:

- This product should be maintained /

serviced and inspected annually by a
qualified service technician.

- This manual is intended for use by a

qualified Installer/Service Technician.

Please reference the unit’s model num-

ber and the serial number from the rat-

ing label, on the backside of the control

panel when inquiring about service or

troubleshooting.

Triangle Tube accepts no liability for any

damage resulting from incorrect instal-

lation or from the use of components or

fittings not specified by Triangle Tube.

NOTICE

NOTICE

WARNING

Summary of Contents for Prestige Slol 250


























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands