manualshive.com logo in svg

TriangleTube Prestige Slol 250, Installation And Maintenance Manual

Share
Download
TriangleTube Prestige Slol 250 Installation And Maintenance Manual Download Page 10

Pre-Installation Items

-

Reference the appropriate vent supple-
ment for clearance requirements.

To provide serviceability to the unit it is

recommended that the following clear-

ances be maintained:

Top boiler jacket - 24 inches [610 mm].
Front  - 24 inches [610 mm].
Bottom boiler piping  - 24 inches [610

mm].
Rear - 0 inches
Sides  - 6 inches [153 mm]

If the clearances listed above cannot be

maintained or the enclosure in which the

boiler is installed is less than 85 cubic feet,

the space must be ventilated. See page 6

for ventilation requirements.

When maintaining zero clearance or less

than recommended clearances, some

product labeling may become hidden

and unreadable.

When installing the PRESTIGE Solo  in

a confined space, sufficient air must be

provided for proper combustion and

venting and to allow, under normal oper-

ating conditions, proper air flow around

the product to maintain ambient temper-

atures within safe limits  to comply with

the National Fuel Gas Code NFPA 54 -

latest edition.

Residential Garage Installations

When installing the PRESTIGE Solo  in a resi-
dential garage, the following special precautions
per NFPA 54/ANSI Z223.1 must be taken:

-

Mount the unit a minimum 18 inches
[458 mm] above the floor level of the
garage.  Ensure the burner and ignition
devices / controls are no less than 18
inches [458 mm] above the floor level.

-

Locate or protect the unit in a manner
so it cannot be damaged by a moving
vehicle.

Boiler Freeze Protection Feature

The boiler control has a freeze protection feature
built in. This feature monitors the boiler temper-
ature and responds as follows when no call for
heat is present:

-

46ºF Boiler circulator is ON

-

38ºF Boiler circulator is ON and burner
operates at low fire

-

50ºF Burner OFF and boiler circulator
operates for approximately 10 minutes

The boiler freeze protection feature is

disabled during a hard lockout, however

the CH circulator will operate.

The boiler freeze protection feature is

designed to protect the boiler. The boiler

should be installed in a primary/sec-

ondary piping arrangement if it is

installed in an unheated space or

exposed to water temperatures of 46ºF or

less. See Section IV for primary/sec-

ondary piping examples. See Section IX

for antifreeze guides.

CAUTION

CAUTION

WARNING

NOTICE

WARNING

BEST PRACTICES

4

Summary of Contents for Prestige Slol 250


























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands