Tri-Star M100LFG-TT-A Owner'S Manual Download Page 41 | Manualshive

Page: 41 / 59

background image

41

No part of this document may be reproduced, stored in retrieval system or transmitted by

any means, electronic, mechanical, photocopying, recording or otherwise, without written
permission from Tri-Star Technologies.

9.5.Laser Parameters and Energy Offset Screens

Laser Configuration is used for laser diagnostics and/or laser tuning only. All values are

factory set for optimum laser performance.

Warning !!!

Do not change any settings unless instructed by authorized

factory representative.

Fig.9.11. Laser Configuration and Energy Offset

Laser ON/OFF

button turns the Q-Switch on and off

Temperature

boxes display the current and set temperatures of the laser crystals and diode.

Arrow

buttons are used to change the vlaues.

Save

button saves the current setting.

Start Power Test

moves the laser beam into the Beam Dump tube and turns the Q-Switch on.

The button is disabled when laser diode is off. To measure the laser power press the Start Power
Test button. The Power measured in Watts will be displayed. Press Stop Power Test to turn off
the Q-Switch.

Energy Offset screen is used to direct the beam into the beam dump tube:

Laser On

turns the Low energy pilot beam on.

«
...
39
40
41
42
43
...
»

Summary of Contents for M100LFG-TT-A




























































Reviews:

No comments

Related manuals for M100LFG-TT-A

Brand: Jennov Pages: 50

Brand: Labom Pages: 5

Brand: Kane Pages: 19

Brand: Keithley Pages: 201

Brand: Garmin Pages: 120

Brand: Major tech Pages: 16

Brand: Zoetis Pages: 2

BUCKMASTERS 1500

Brand: Sig Sauer Pages: 2

Brand: WIKA Pages: 88

Brand: PITSID Pages: 22

Brand: Swan Analytical Instruments Pages: 102

Microlog GX Series

Brand: SKF Pages: 342

Brand: E+E Elektronik Pages: 32

Brand: Proteus Pages: 4

Brand: Kawai Pages: 2

Brand: Harken Pages: 2

Brand: Huvitz Pages: 58

LaserDIMENSIONMASTER 3336

Brand: Calculated Industries Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands