Tri-Star M100LFG-TT-A Owner'S Manual Download Page 24 | Manualshive

Page: 24 / 59

background image

24

No part of this document may be reproduced, stored in retrieval system or transmitted by

any means, electronic, mechanical, photocopying, recording or otherwise, without written
permission from Tri-Star Technologies.

4.5. Operator Work Station

The operator workstation consists of a regular laptop computer that can be configured to

the customer's specifications. The operator can input information using a keyboard, memory
stick, LAN, etc. In the marker mode computer has Ethernet connection with PLC, RS-232 Serial
connection with Laser, and regular USB to USB connection with ScanAlone board.

White start and Red Power off/emergency-stop buttons are conveniently located on the

front panel of the cabinet. When powered and connected to the air supply machine is completely
ready for wire processing (Fig.4.9).

Fig.4.9. Operator workstation.

«
...
22
23
24
25
26
...
»

Summary of Contents for M100LFG-TT-A




























































Reviews:

No comments

Related manuals for M100LFG-TT-A

Brand: Kanomax Pages: 26

Brand: Macnaught Pages: 20

Brand: Calsense Pages: 4

Brand: Keithley Pages: 32

Brand: M & I Instruments Pages: 2

Brand: Teledyne Analytical Instruments Pages: 107

Brand: Barksdale Pages: 2

Brand: Lutron Electronics Pages: 13

Brand: H-Star Pages: 36

WJ-NX310K Series

Brand: i-PRO Pages: 18

Brand: CWT Pages: 41

Brand: Leutert Pages: 8

Brand: Erma Electronic Pages: 24

NEO MP18X Series

Brand: MA Pages: 3

Brand: Hanna Instruments Pages: 2

Brand: Hameg Pages: 6

Brand: TA ENGINEERING Pages: 22

Brand: NI Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands