Travis Industries Lopi GreenField GS Owner'S Manual Download Page 64

Page: 64 / 64

Index

4101028

100-01255_000

Approved Vent Configurations ............................. 15

Adjusting the Blower Speed ................................. 36

Adjusting the Flame Height .................................. 35

Air Shutter Adjustment ......................................... 25

Altitude Considerations ........................................ 14

Blower Control ...................................................... 36

BTU Input ............................................................. 6

BTU Output .......................................................... 6

Cap (see vent termination) ................................... 23

Chimney Cap (see vent termination) ................... 23

Clearances ........................................................... 9

Condensation on Glass ........................................ 35

Corner Installation ................................................ 9

Dimensions .......................................................... 6

Elbows .................................................................. 15

Finalizing the Installation ...................................... 24

Floor Protection ................................................... 11

Fuel ...................................................................... 4

Gas Inlet Pressure ............................................... 13

Gas Line Connection ........................................... 13

Gas Line Install .................................................... 13

Gas Smell ................................... See Inst. on Cover

Glass Installation and Removal ........................... 26

Hearth Requirements ........................................... 11

Heating Specifications ......................................... 6

Horizontal Vent Termination Requirements ......... 23

Installation Options .............................................. 6

Items Required for Installation ............................. 7

Leaking Gas ............................... See Inst. on Cover

Listing Information ............................................... 44

Location of Controls ............................................. 34

Log Set Installation and Removal ........................ 28

Maintenance ........................................................ 38

Measuring Vent Lengths ...................................... 16

Noise (see Normal Operating Sounds)................ 37

Normal Operating Sounds ................................... 37

Packing List .......................................................... 7

Piping Installation (see Gas Line Install) ............. 13

Restrictor Position ................................................ 15

Safety Label ......................................................... 44

Safety Precautions ............................................... 4

Starting the Stove for the First Time .................... 35

Thermostat Operation .......................................... 35

Turning the Stove On and Off .............................. 35

Vent Length (see “Vent Config.”) ......................... 16

Vent Requirements .............................................. 11

Vertical Vent Termination Requirements ............. 23

Warnings .............................................................. 4

Warranty .............................................................. 40

Water on Glass (see Condensation) ................... 35

Weight .................................................................. 6

Wiring Diagram .................................................... 42

Yearly Service Procedure .................................... 40

Summary of Contents for Lopi GreenField GS

































































Search results

Summary of Contents for Lopi GreenField GS

Reviews:

Related manuals for Lopi GreenField GS

Brands by name

Popular brands

Travis Industries Lopi GreenField GS, Owner'S Manual

Search results

Summary of Contents for Lopi GreenField GS

Reviews:

Related manuals for Lopi GreenField GS

Brands by name

Popular brands