Travis Industries Lopi GreenField GS Owner'S Manual Download Page 41

Page: 41 / 64

Maintenance

(for qualified service personnel only)

4101028

100-01255_000

Troubleshooting Table

Problem:

Possible Cause:

Don't Call for Service

Until You:

Main Burners Will

Not Start

The ON/OFF switch is turned to "OFF"

The remote control is not working correctly

The thermostat is disconnected or set too low

No Propane in Tank

Turn the ON/OFF switch to "ON"

See the remote control instructions

See "Thermostat Operation"

Check Tank Level

Receiver Beeps

The power backup batteries are dead

Replace the batteries (see page 38)

Thermostat Does

Not Work

The ON/OFF switch is turned to "OFF"

The thermostat is set too low

Turn the ON/OFF switch to "ON"

Check thermostat

Stove Will Not

Distribute Heat

The stove is not getting electricity

The stove is not up to temperature

Check the breaker switch

Let the stove burn for at least 15 minutes

Flames Are Too

Blue

The stove has just been started

Improper air shutter adjustment

This is normal - see "Starting the Stove for
the First Time"

Adjust Air Shutter - contact your dealer

Flames Are Too

Short (Under 6")

The flame height may be turned too low

Turn the flame height to "HI" -
See "Adjusting the Flame Height"

Comfort Control

Does not Work

The AA batteries may be dead

Replace the AA batteries (see page 38)

Thin Layer of Soot

Covers the Glass

The logs or coals are placed incorrectly

Improper air shutter adjustment

See "Log Set Installation"

Adjust Air Shutter - contact your dealer

Summary of Contents for Lopi GreenField GS

































































Search results

Summary of Contents for Lopi GreenField GS

Reviews:

Related manuals for Lopi GreenField GS

Brands by name

Popular brands

Travis Industries Lopi GreenField GS, Owner'S Manual

Search results

Summary of Contents for Lopi GreenField GS

Reviews:

Related manuals for Lopi GreenField GS

Brands by name

Popular brands