Travis Industries Lopi GreenField GS Owner'S Manual Download Page 3

Page: 3 / 64

Table of Contents

4101028

100-01255_000

Introduction

Introduction & Important Information ................... 2

Safety Precautions

Safety Precautions .............................................. 4

Features & Specifications

Features .............................................................. 6

Installation Options ............................................. 6

Heating Specifications ......................................... 6

Dimensions ......................................................... 6

Installation

Installation Warning............................................. 7

Packing List ......................................................... 8

Additional Items Required for Installation ............ 8

Installation Overview ........................................... 8

Installation Hints .................................................. 8

Stove Clearances ................................................ 9
Mobile Home Requirements ................................ 11

Heater Placement Requirements ........................ 11

Floor Protection Requirements ........................... 11

Electrical Requirements ...................................... 11

Optional Wall Switch or Thermostat Installation .. 12

Gas Line Installation............................................ 13

Vent Requirements ............................................. 14

Approved Vent Configurations ............................ 15

Exhaust Restrictor Position ........................... 15

Closing the Diffuser ....................................... 16

Exhaust Restrictor Extender .......................... 17

Measuring Vent Lengths ............................... 17

Rear Vent Configuration with No Rise ........... 18

Rear Vent with Horizontal Termination .......... 19

Rear Vent with Vertical Termination .............. 20

Top Vent with Horizontal Termination ........... 21

Top Vent with Vertical Termination ................ 22

Vent Termination Requirements ......................... 23

Finalizing the Installation

Leak Test ............................................................ 24

Pilot Adjustment (if necessary) ............................ 24

Air Shutter Adjustment (if necessary) .................. 25

Check Flame ....................................................... 25

Face and Glass Removal .................................... 26

Log Installation .................................................... 28

Operation

Before You Begin ................................................ 34

Location of Controls ............................................ 34

Starting the Stove for the First Time ................... 35

Turning the Stove On and Off ............................. 35

Comfort Control ................................................... 35

Adjusting the Flame Height ................................. 35

Accent Light ........................................................ 36

Adjusting the Optional Blower Speed .................. 36

Continuous Pilot / GreenSmart™ Pilot Switch..... 36

Normal Operating Sounds ................................... 37

Normal Operating Odors ..................................... 37

Maintenance

Maintaining Your Stove’s Appearance ................ 38

Battery Replacement ........................................... 38

Accent Light Replacement .................................. 39

Yearly Service Procedure ................................... 40

Troubleshooting Table ........................................ 41

Wiring Diagram ................................................... 42

Replacement Parts List ....................................... 43

Safety Label

Safety Label ........................................................ 44

Warranty

Warranty ............................................................. 40

Optional Equipment

LP Conversion Instructions ................................. 46

GreenSmart™ Remote Control Installation ......... 52

Index

Index ................................................................... 64

Summary of Contents for Lopi GreenField GS

































































Search results

Summary of Contents for Lopi GreenField GS

Reviews:

Related manuals for Lopi GreenField GS

Brands by name

Popular brands

Travis Industries Lopi GreenField GS, Owner'S Manual

Search results

Summary of Contents for Lopi GreenField GS

Reviews:

Related manuals for Lopi GreenField GS

Brands by name

Popular brands