Travis Industries Lopi GreenField GS Owner'S Manual Download Page 12

Page: 12 / 64

Installation

(for qualified installers only)

4101028

100-01255_000

Optional Wall Switch or Thermostat Installation

Do not connect 110-120 VAC to the gas control valve or wiring system of this stove. The switch must

be installed by a qualified installer.

This stove may be installed with an optional wall switch or thermostat. The thermostat (or on/off switch)
wires will interrupt the burner circuit (see item “a” below).

1. If you wish to bypass the switch, connect the thermostat (on/off switch) wires directly to the green and

white wires (see “a” below).

2. If you wish keep the switch and connect the wires in parallel or series, use wire splitters.

White

Green

ON / OFF

COMFORT

CONTROL

BATTERY

TRAY

MAIN

BURNER

Red

Black

Red

Blue

Red

Blue

Black

POWER SUPPLY

Burner Circuit Wires

Summary of Contents for Lopi GreenField GS

































































Search results

Summary of Contents for Lopi GreenField GS

Reviews:

Related manuals for Lopi GreenField GS

Brands by name

Popular brands

Travis Industries Lopi GreenField GS, Owner'S Manual

Search results

Summary of Contents for Lopi GreenField GS

Reviews:

Related manuals for Lopi GreenField GS

Brands by name

Popular brands