background image

 

 

 

Featuring the

 

 

Burner

 

•  Direct Vent Freestanding Stove 

•  Natural Gas or Propane 

•  Vent Horizontally or Vertically 

•  Standard Residential  

•  Mobile Home Approved 

Tested and Listed by 

 

ANSI Z21.88 CSA 2.33 

 

WARNING

If the information in these instructions is not followed exactly, a fire or 
explosion may result causing property damage, personal injury or loss of 
life. 

-  Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this 

or any other appliance. 

WHAT TO DO IF YOU SMELL GAS 

•  Do not try to light any appliance. 
•  Do not touch any electrical switch; do not use any phone in your building. 
•  Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's 

instructions. 

•  If you cannot reach your gas supplier, call the fire department. 

-  Installation and service must be performed by a qualified installer, service agency or the 

gas supplier. 

 

This appliance may be installed in an 

aftermarket permanently located, 
manufactured home (USA only) or mobile 
home, where not prohibited by local 
codes. 

This appliance is only for use with the 
type(s) of gas indicated on the rating plate.  
A conversion kit is supplied with the 
appliance.

 

 

GreenField 

 

Owner’s Manual 

INSTALLER

Leave this manual with the appliance. 

CONSUMER:

   Retain this manual for future reference. 

©

 Copyright 2010, T.I.        $10.00       100-01255_000       4101028 

 

www.travisproducts.com 

4800 Harbour Pointe Blvd. SW 

Mukilteo, WA  98275

 

 

Summary of Contents for Lopi GreenField GS

































































Reviews: