background image

Neptune 5500

28

LIMITED WARRANTY

Seller warrants that the NEPTUNE Series Digital Indicator line will conform to written

specifications, drawings, and other descriptions made by the manufacturer, including any

modifications thereof. The Seller warrants the goods against faulty workmanship and defective

materials. If any goods fail to conform to these warranties, Seller will, as its sole and exclusive

liability hereunder, repair or replace such goods if they are returned within the following warranty

period:

Twelve (12) months from date of shipment from manufacturer.

These warranties are made upon the following TERMS and CONDITIONS:

This warranty is limited to the original equipment manufactured by TRANSCELL
TECHNOLOGY, INC. Items not covered under this warranty are batteries and normal wear
items like connectors, shrouds, front panels and fuses.
For the first sixty (60) days from the date of installation, the warranty covers parts, on-site
labor, and limited travel time and mileage. (3 hrs/150 miles maximum per occurrence).
After sixty (60) days, the warranty covers the cost of replacement parts only.
However, at the discretion and prior approval of TRANSCELL, certain equipment may be
returned , freight pre-paid, for repair, free of any parts or labor charges.  

TRANSCELL’s responsibility is confined to repair, replacement or credit of equipment of
parts. The warranty does not extend coverage to labor, material, freight or service charges
involved in removal, shipping or reinstallation of equipment or parts.

CONDITIONS WHICH VOID LIMITED WARRANTY:
This warranty shall not apply to equipment which:
A. Examination of such goods discloses that the nonconformity exists and was caused by

accident, misuse, neglect, alteration, improper installation improper or unauthorized repair,
improper testing, or an act of GOD including lightning and such goods have not been
modified, altered, or changed by any person other than the Seller or its duly authorized repair
agents.

Transcell Technology, Inc. will have a reasonable time to repair or replace such goods.

THESE WARRANTIES EXCLUDE ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, ORAL

OR WRITTEN, INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY

OR FITNESS FOR A PARTICULAR PURPOSE. SELLER WILL NOT IN ANY EVENT BE LIABLE

FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.

IN ACCEPTING THIS WARRANTY, THE PURCHASER OR BUYER AGREES TO WAIVE ANY

AND ALL OTHER CLAIMS FOR RIGHT TO WARRANTY FROM TRANSCELL TECHNOLOGY,

INC. SHOULD THE SELLER BE OTHER THAN TRANSCELL TECHNOLOGY, INC., THE

BUYER AGREES TO LOOK ONLY TO THE SELLER FOR WARRANTY CLAIM OR CLAIMS.

No terms, conditions, understanding, or agreements purporting to modify the terms of this

warranty shall have any legal effect unless made in writing and signed by a corporate officer of

the Seller.

Summary of Contents for NEPTUNE-5500 Series





























Reviews: