background image

Programming Status

PKG-SVP01E-EN

19

Active OA Temperature Sensor Input From
RTM OUTSIDE AIR TEMP INPUT 

is 86.0 F

Possible Values: RTM Outside Air Temp Input, ICS 
(Tracer Summit™)

1.

Pressing the NEXT key will scroll forward through the screens.

Active Outside Air Humidity Sensor Input From

Used With: Units with an airside economizer.
Possible Values: O/A Humidity Sensor Input, ICS 
(Tracer Summit™) 
Sensor Range: 0 - 100%

OA HUMIDITY SENSOR INPUT 

Is 30%

1.

Pressing the NEXT key will scroll forward through the screens.

Active Supply Air Press Sensor Input From

Used With: Units with IGV, VFD or with the SAP 
sensor enabled
Possible Values: RTM SA PRessure Input, ICS 
(Tracer Summit™)

RTM SA PRESSURE INPUT is

2.1 IWC

1.

Pressing the NEXT key will scroll forward through the screens.

Temp Sensor Input Being Monitored

Possible Values:  RTM Zone Temp Input, NSB Zone 
Sensor Setpoint Input, RTM Aux Temp Input, ECEM 
return Air Temp Input, ICS (Tracer Summit™)
Sensor Range: -40 to 200 F

RTM ZONE TEMP INPUT is 

82.0 F

1.

Pressing the NEXT key will scroll forward through the screens.

End of Submenu (NEXT) to Enter SETUP

1.

Press the NEXT key until the following screen is displayed. (if applicable)

Temperature Input Status Submenu
Press ENTER to View Data in This Submenu

1.

Pressing the NEXT key will scroll forward through the screens.

Temp Meausured By Sensor Connected To
RTM ZONE TEMP INPUT

82.0 F

1.

Press the NEXT key until the following screen is displayed. (if applicable)

Temp Meausured By Sensor Connected To
RTM SUPPLY AIR TEMP INPUT

50.0 F

1.

Press the NEXT key until the following screen is displayed. (if applicable)

Temp Measured By Sensor Connected To
NSB Panel Temp Sensor Input

79.5 F

Used With: Units with NSB zone sensor installed.

1.

Press the NEXT key until the following screen is displayed. (if applicable)

Temp Measured By Sensor Connected To
RTM AUX TEMP INPUT

62.0 F

1.

Press the NEXT key until the following screen is displayed.

Temp Measured By Sensor Connected To 
RTM OUTSIDE AIR TEMP INPUT

86.0 F

1.

Press the NEXT key until the following screen is displayed.

Temp Measured By Sensor Connected To 
HEAT MODULE AUX TEMP INPUT 

82.0 F

Used With:   Units with hydronic, electric, or 
external heat only

1.

Press the NEXT key until the following screen is displayed. (if applicable)

Temp Measured By Sensor Connected To
ECEM RETURN AIR TEMP INPUT 

78.0 F

Used With:  Units with a VCM and OA preheater 
enabled.

1.

Press the NEXT key until the following screen is displayed.

Summary of Contents for IntelliPak SCRG-020





















































Reviews: