Trane IntelliPak SCRG-020 Programming Manual Download Page 38 | Manualshive

Page: 38 / 52

background image

SETPOINT Menu

38

PKG-SVP01E-EN

Low Ambient Comp Lockout Temp:

50 F

Used With: All Units
Factory Presets: 50 F
Possible Values: -20 F to 80 F

Comp(s) OFF if OA Temp Below This Value

1.

Press the NEXT key until the following screen is displayed.

Setpoint Source Selections Submenu

Used With: All Units

Press ENTER to Review or Adjust

1.

Press the NEXT key until the following screen is displayed.

For Supply Air Temp Cooling Control,

Use

Used With: All Units
Factory Presets: HI (Keypad) Setpoint Menu
Possible Values: HI (KEYPAD) SETPOINT
MENU, ZONE SENSOR SETPOINT MENU, NSB
PANEL SETPOINT INPUT, GBAS 0-5 VDC
MODULE

Setpoint From: HI (KEYPAD) SETPOINT MENU

1.

Press the NEXT key until the following screen is displayed.

For Supply Air Temp Heating Control,

Use

Used With: All Units when hydronic or electric
heat is installed.
Factory Presets: HI (Keypad) Setpoint Menu
Possible Values: HI (KEYPAD) SETPOINT
MENU, GBAS 0-5VDC Module

SETPOINT From: HI (KEYPAD) SETPOINT MENU

1.

Press the NEXT key until the following screen is displayed.

For Occ Zone Temp Cooling Control, Use

Used With: All Units
Factory Presets: HI (KEYPAD) SETPOINT
MENU
Possible Values: HI (KEYPAD) SETPOINT
MENU, ZONE SENSOR SETPOINT INPUT, NSB
PANEL SETPOINT INPUT, GBAS 0-5 VDC
MODULE

SETPOINT From: HI (KEYPAD) SETPOINT MENU

1.

Press the NEXT key until the following screen is displayed.

For Occ Zone Temp Heating Control, Use

Used With: All Units with hydronic or electric
heat.
Factory Presets: HI (KEYPAD) SETPOINT
MENU
Possible Values: HI (KEYPAD) SETPOINT
MENU, ZONE SENSOR SETPOINT INPUT, NSB
PANEL SETPOINT INPUT, GBAS 0-5 VDC

MODULE

SETPOINT From: HI (KEYPAD) SETPOINT MENU

1.

Press the NEXT key until the following screen is displayed.

For Unocc Zone Temp Cooling Control, Use

Used With: All Units
Factory Presets: HI (KEYPAD) SETPOINT
MENU
Possible Values: HI (KEYPAD) SETPOINT
MENU, ZONE SENSOR SETPOINT INPUT, NSB
PANEL SETPOINT INPUT, GBAS 0-5 VDC
MODULE

Setpoint From: HI (KEYPAD) SETPOINT MENU

1.

Press the NEXT key until the following screen is displayed.

For Unocc Zone Temp Heating Control, Use

Used With: All Units when External, Electric or
Hydronic Heat is installed
Factory Presets: HI (KEYPAD) SETPOINT
MENU
Possible Values: HI (KEYPAD) SETPOINT
MENU, ZONE SENSOR SETPOINT INPUT, NSB
PANEL SETPOINT INPUT, GBAS 0-5 VDC
MODULE, GBAS 0-10VDC Module

Setpoint From: HI (KEYPAD) SETPOINT MENU

1.

Press the NEXT key until the following screen is displayed.

For Morning Warmup Temp Control, Use

Used With: All Units when Electric, External or
Hydronic Heat is installed
Factory Presets: HI (KEYPAD) SETPOINT
MENU
Possible Values: HI (KEYPAD) SETPOINT
MENU, NSB PANEL SETPOINT INPUT
GBAS 0-5VDC Module

Setpoint From: HI (KEYPAD) SETPOINT MENU

1.

Press the NEXT key until the following screen is displayed.

«
...
36
37
38
39
40
...
»

Summary of Contents for IntelliPak SCRG-020





















































Reviews:

No comments

Related manuals for IntelliPak SCRG-020

Brand: Dometic Pages: 2

Air scat RF-17F series

Brand: Fuji Electric Pages: 30

Brand: Heylo Pages: 26

Brand: A.O. Smith Pages: 16

FMV-ND100PLS/A-T

Brand: Fluo Pages: 28

Brand: Vaillant Pages: 168

Brand: ICP Pages: 13

Brand: Daikin Pages: 44

Cold Wall Evaporator Open Front Milk Coolers OMC Series

Brand: Master Bilt Pages: 2

Brand: Airwell Pages: 115

TAC-07CHSA/XA71

Brand: TCL Pages: 41

Brand: Dadam micro Pages: 12

Brand: Airwell Pages: 12

Brand: Daikin Pages: 88

Brand: Daikin Pages: 48

Brand: Panasonic Pages: 128

Brand: Panasonic Pages: 76

VORTEX UV36C2DB1

Brand: innovair Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands