background image

DIAGNOSTICS Menu

PKG-SVP01E-EN

47

Failure Modes

When any condition results in the rooftop unit’s inability to

perform a normal function, it is said to have entered a
failure mode. There are two types of failure modes.

1. An “Analog input out of range” failure mode.

This failure mode occurs when a sensing device such

as a zone temperature sensor or a humidity sensor
begins to transmit information that is outside its
allowable range.

2. A “Fault recognition by input logic” failure mode.

This failure mode occurs when the UCM receives

information that does not “make sense” or does not
conform to its predefined logic.

Diagnostics Types

There are three types of diagnostics:

1.

Informational - Does not affect machine operation.

2. Automatic Reset - Affects machine operation but

returns to normal when diagnostic condition no longer
exists.

3. Manual Reset - Affects machine operation and must be

reset at the HI or by cycling power to unit for normal
operation to resume.

To troubleshoot diagnostics, reference the Installation,

Operation, and Maintenance Manual SCXF-SVX01*-EN

that ships with the Signature Series units and SCXG-
SVX01*-EN that ships with the Modular Series units.

Log 1                                              ___________________
___________________                

Possible Values:

Log number 1-20

Manual

Viewed or Not Viewed

Auto

Active or History

Info

Or any diagnostic listed under the previous screens associated with the diagnostic type 
including VOM activated mode

1.

Press the CANCEL key to clear the diagnostics and prompt the following screen.

Diagnostic Log is Password Protected

Possible Values: + (Plus), - (Minus)

Please Enter Password:       ___________________          

1.

Press the + (Plus) or - (Minus)keys to enter the password.

2.

Press the ENTER key to confirm. After entering the correct password, the following screen will display.

Active Diagnostics        ___________________          

Possible Values: Manual, Auto, or Info

Please Wait, Updating Diagnostic Log

If the DIAGNOSTIC LOG is empty when the CANCEL key is pressed, the following screen will display.

Active Diagnostics        Info

Possible Values: Manual, Auto, or Info

Diagnostic Buffer Is Already Empty!

Press the AUTO or STOP key to return to the top level status screen.

Summary of Contents for IntelliPak SCRG-020





















































Reviews: