background image

GENERAL SYSTEM CONFIGURATION

Configuring SIP Server Settings

1-16

IP4100 Install   Sept., 2013

Configuring SIP Server

Settings

The SIP server is the IPedge or Strata CIX system.

1.

In the Network screen (refer to 

Figure 1-10

) ensure that the 

parameters under the SIP/RTP Settings are correct.

2.

In the left panel of the screen, select Servers. This opens the Servers 
screen. 

Figure 1-12   Servers screen

3.

Click on 

Add Server

, then enter the necessary information for the first 

IPedge or Strata CIX system. Refer to 

Table 1-5

.

NO

Table 1-5

SIP Server Setting Parameters

Parameter

Meaning

NAT Adaptation

NO:

 The Base Station disregards information from the report and 

Received parameters. This is the typical configuration.

YES

: If information in the report and received parameters is different 

from local information, the Base will perform new SIP registration with 
the new information in the Contact header. If information in report and 
Received parameters is not different from local information then no 
action is performed.

SIP Server

Enter the IP address of the IPedge server or the MIPU card of the 
Strata CIX system. If desired, you can add the port number after the IP 
address using the format {IPadddress}:{port}”

Outbound Proxy

If there is a SIP Proxy, between the base station and the IPedge or 
Strata CIX system, enter the IP address of the SIP Proxy. If desired, 
you can add the port number after the IP address using the format 
{IPaddress}:{port} (e.g., 192.168.250.111:5060).

 (Sheet 1 of 2)

Summary of Contents for IP4100 Series

























































































Reviews: