manualshive.com logo in svg

Toshiba IP4100 Series, Installation Manual

Share
Download
Toshiba IP4100 Series Installation Manual Download Page 49

MULTI-CELL SYSTEM SETUP

Configure Level 2 (and Up) Base Stations

IP4100 Install   Sept., 2013

1-27

source, there will be a warning in the DECT Chain for this base 
station.

Figure 1-22   Base Station Group Table, Synchronization Complete (Multi-cell Screen)

      

13. When the system has finished synchronizing, repeat this process for 

each base station at Level 1.

Figure 1-23   Base Station Group Table, Level 1 Complete (Multi-cell Screen)

     

Configure Level 2 (and

Up) Base Stations

1.

Place the first Level 2 base station at its final location. (See the 
Network Planning Guide for information on the proper placement of 
base stations.)

2.

Login to the base station.

3.

Reset the base station to its default settings (open the Management 
screen and click Default Base Station). If this base station has never 
been configured, skip this step. 

Summary of Contents for IP4100 Series

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands