SUA 125 NUMERIC
34200003
TOS a.s. 02/2011
18
Safety information
It is in accordance with EN 292-2, the article 5 in this Manual.
Marking
clamping device of workpiece (face plate) is marked with the max. admissible speed.
Manual
This Manual is in accordance with EN 292 demands, the article 5.5.
The following data are mentioned in this Manual and selling literature:
- noise emission values
- principles of test making
- general safety principles for the lathe operation.
Tool exchange
The information which allows safety chucking and tool exchange is mentioned in this Manual, e.g. data refering to this part
of dividing line tool - machine, which belongs to the lathe.
Exchange of workpiece chucking device
This Manual contains the information which allows the safety fastening and exchange of workpiece chucking device, e.g.
data refering to the part of dividing line chucking device - machine, which belongs to the lathe.
Using of workpiece chucking device
The sufficient information for chucking device delivered with lathe is mentioned in this Manual. The information anables
the safety usage of the chucking device (basic information of face plate).
Adaptation of workpiece chucking device
The Manual information of the adaptation of workpiece chucking devices delivered separately with the lathe or fastened can
limit or change the max. operating speed or efficiency of these devices.
If the chucking device is supplied with another equipment or if some equipment is replaced by another one, which can limit
the max. speed, this device must be explicitly indicated with the limited max. speed.
Remaining risk factors
The manufacturer gives an information of the strengh of protective shields delivered with the lathe. The protective shields
fitted on the lathe or delivered with the lathe are mentioned in this Manual. They can minimalize only the risk of throwing
up and cannot eliminate it at all.
In cases where the risk of throwing up can be higher than that is expected or mentioned in the method of protective shield
tests, the designer, producer and supplier must give some information about these remaining risk factors ( solutions of
single technological cases ).
Action on CNC panel
Information given by manufacturer contains the action on CNC panel, for example tool correction, mode selection, change
of mode etc. is in this Manual.
WARNING!
External equipment - portable PC - (or other equipment) can be connected to the machine through the RS 232-C only in
case that the system has been switched off.
Non-observing this procedure can expose the customer to the risk of damage of the control system or the connected external
equipment!
Perfectly attested components and principles
a)Electrical equipment is in accordance with following Standards:
Summary of Contents for SUA 125 NUMERIC
