Toro Z 440 Pro Value Series Page 52 Service Manual Download

Page: 52 / 190

3-21

Z Master Z400 Service Manual

Fig 103

PICT-0045

5. Remove the brake bar from the machine (Fig. 103).

Brake Installation

CHASSIS

Check the parking brake for proper adjustment.

1. Check tire pressure of all 4 tires.

2. Disengage the brake lever (lever down).

Reverse the order of removal

Adjusting the Parking Brake

3. Measure the distance vertically between the front

of the brake bar and the crown of the tire; the

measurement should be 7/8” to 1” (22 to 25mm)

(Fig. 104).

Fig 104

Figure 45

1. Brake lever

5. Vertical line from the

2. Tire

front of brake bar to the

3. Brake bar

tire crown

4. 7/8” to 1” (22 to 25mm)

Summary of Contents for Z 440 Pro Value Series































































































































































































Search results

Summary of Contents for Z 440 Pro Value Series

Reviews:

Related manuals for Z 440 Pro Value Series

Brands by name

Popular brands

Toro Z 440 Pro Value Series, Service Manual

Search results

Summary of Contents for Z 440 Pro Value Series

Reviews:

Related manuals for Z 440 Pro Value Series

Brands by name

Popular brands