Toro Polar Trac Cab 30474 Operator'S Manual Download Page 10

Page: 10 / 60

g032391

Figure 5

Seat connector

Wire clip

Wire harness

Remove the wire clip from the bottom of the seat
deck

Figure 5

Clean the bottom of the seat deck to ensure
proper adhesion of the under-seat shield.

Remove the backing and apply the under-seat
shield to the bottom of the seat deck (

Figure 6

g032392

Figure 6

Heat shield

Cutout

Note:

Use the cutouts for the bolts to align the

under-seat shield to the plate.

Install the wire clip to the bottom of the seat
plate (

Figure 7

g032393

Figure 7

Hole for wire clip

Wire clip

Connect the seat-switch to the wire harness
(

Figure 7

Assembling the Heater
Hoses

Parts needed for this procedure:

Straight fitting (3/8 NPT x 0.625 barb)

Hose clamp (1/2 to 1-1/4 inches)

Hose clamp (3/4 to 1-1/2 inches)

Tee fitting

Female-dust fitting

Male-dust fitting

Assembling the Supply Hose

Note:

Use the 86.3 cm (34 inches) hose for a

machine equipped with the Yanmar engine and
use the 57.1 cm (22.5 inches) hose for a machine
equipped with the Kubota engine.

Apply sealant to the straight fitting (3/8 NPT x
0.625 barb); skipping the first thread.

Summary of Contents for Polar Trac Cab 30474





























































Search results

Summary of Contents for Polar Trac Cab 30474

Reviews:

Related manuals for Polar Trac Cab 30474

Brands by name

Popular brands

Toro Polar Trac Cab 30474, Operator'S Manual

Search results

Summary of Contents for Polar Trac Cab 30474

Reviews:

Related manuals for Polar Trac Cab 30474

Brands by name

Popular brands