Calibrating the Sprayer Speed
1.
Ensure that the sprayer tank is filled with water.
2.
On an open, flat area, mark off a distance
between 45–152 m (150–500 ft).
Note:
Toro recommends marking off 152 m
(500 ft) for more accurate results.
3.
Start the engine and drive to the start of the
marked-off distance.
Note:
Align the center of the front tires with the
starting line for the most accurate measurement.
4.
On the InfoCenter, navigate to the Calibration
menu and select Speed Calibration.
Note:
Selecting the Home Screen icon at any
time will cancel calibrations.
5.
Select the Next arrow (→) on the InfoCenter.
6.
Using the plus (+) and minus (-) symbols, enter
the marked-off distance into the InfoCenter.
7.
Perform one of the following:
•
For HD-Series Models with a
manual
transmission
—shift the machine into first
gear and drive the marked distance in a
straight line at full throttle.
•
For the
HDX-Auto model
,—shift the
machine into D (drive ) and drive the marked
distance in a straight line at full throttle.
8.
Stop the machine at the marked-off distance
and select the check mark on the InfoCenter.
Note:
Slow down and roll to a stop to align the
center of the front tires with the finish line, for
the most accurate measurement.
Note:
Calibration is now complete.
Calibrating the Boom Bypass
Important:
Select an open flat area to perform
this procedure.
Note:
Calibrating the boom bypass for
machines
without a throttle lock
requires 2 people.
1.
Ensure that the sprayer tank is filled with water.
2.
Set the transmission as follows:
•
For HD-Series Models with a
manual
transmission
—shift the transmission to
Neutral
•
For the
HDX-Auto model
—shift the
transmission to P (park).
3.
Set the parking brake and turn the engine on.
4.
Set the 3 boom switches to the On position, but
leave the
MASTER BOOM
switch off.
5.
Set the
PUMP
switch to the On position, and turn
on the agitation.
6.
Set the engine speed as follows:
•
For machines
without
the optional throttle
lock—have 1 person press down on the
accelerator pedal until maximum engine
speed is reached.
Note:
The other person will adjust the boom
section-bypass valves.
•
For machines
with
the optional throttle
lock, press down on the accelerator pedal
until maximum engine speed is reached
and set the throttle lock; refer to operation
instructions for your Workman hand throttle
kit.
7.
On the InfoCenter, navigate to the Calibration
menu and select Test Speed.
Note:
Selecting the Home Screen icon at any
time will cancel calibrations.
8.
Using the plus (+) and minus (-) symbols, enter
a test speed of 5.6 Km/h (3.5 mph), then select
the Home icon.
9.
Using the
APPLICATION RATE
switch, adjust the
application rate according to the table below.
Nozzle Application Rate Table
Nozzle Color
SI (Metric)
English
Turf
Yellow
159 L/ha
17 gpa
0.39 gpk
Red
319 L/ha
34 gpa
0.78 gpk
Brown
394 L/ha
42 gpa
0.96 gpk
Gray
478 L/ha
51 gpa
1.17 gpk
White
637 L/ha
68 gpa
1.56 gpk
Blue
796 L/ha
85 gpa
1.95 gpk
Green
1,190 L/ha
127 gpa
2.91 gpk
10.
Turn off the left boom and adjust the boom
bypass valve (
) until the pressure
reading is at the previously adjusted level
(typically 40 psi or 2.75 bar).
Note:
The numbered indicators on the bypass
valve are for reference only.
55
Summary of Contents for Multi Pro WM 41240
Page 79: ...Schematics g255886 Flow Diagram Sprayer System DWG 125 0699 Rev B 79...
Page 80: ...Notes...
Page 81: ...Notes...
Page 82: ...Notes...
