background image

The Toro Total Coverage Warranty

Landscape

A Limited Warranty (see warranty periods below)

Contractor
Equipment (LCE)

Conditions and Products Covered

The Toro Company and its affiliate, Toro Warranty Company, pursuant to an
agreement between them, jointly promise to the original purchaser to repair the Toro
Products listed below if defective in materials or workmanship.

The following time periods apply from the date of purchase by the original owner:

Products

Warranty Period

21 in. Mowers

1 year Commercial Use

Engines

4

Honda – 1 years

Kawasaki – 3 years

21 in. Mowers

2 years Residential Use

1

Engines

4

Honda – 2 years

Kawasaki – 3 years

30 in. Mowers

2 years Commercial and Residential Use

1

Engines

4

Kawasaki – 3 years

Mid-Size Walk-Behind Mowers

2 years

Engines

4

Kawasaki – 3 years

Grand Stand

®

Mowers

5 years or 1,200 hours

2

Engines

4

Kawasaki – 3 years

Kohler EFI – 3 years

Frame

Lifetime (original owner only)

3

Z Master

®

2000 Series Mowers

4 years or 500 hours

2

Engines

4

Kawasaki – 3 years

Frame

Lifetime (original owner only)

3

Z Master

®

3000 Series Mowers

5 years or 1,200 hours

2

Engines

4

Kawasaki – 3 years

Frame

Lifetime (original owner only)

3

Z Master

®

5000 Series Mowers

5 years or 1,200 hours

2

Engines

4

Kohler Command – 2 years

Kohler EFI – 3 years

Frame

Lifetime (original owner only)

3

Z Master

®

6000 Series Mowers

5 years or 1,200 hours

2

Engines

4

Kawasaki – 3 years

Kohler Command – 2 years

Kohler EFI – 3 years

Frame

Lifetime (original owner only)

3

Z Master

®

7000 Series Mowers

4 years or 1,200 hours

2

Engines

4

Kubota – 2 years

Briggs & Stratton – 2 years

Frame

Lifetime (original owner only)

3

All Mowers

Battery

90 days Parts and Labor

1 year Parts only

Belts and Tires

90 days

Attachments

1 year

1

Residential use means use of the product on the same lot as your home. Use at more than one

location is considered commercial use and the commercial warranty would apply.

2

Whichever occurs first.

3

Lifetime Frame Warranty - If the main frame, consisting of the parts welded together to form the

tractor structure that other components such as the engine are secured to, cracks or breaks in
normal use, it will be repaired or replaced, at Toro's option, under warranty at no cost for parts
and labor. Frame failure due to misuse or abuse and failure or repair required due to rust or
corrosion are not covered.

4

Some engines used on Toro Products are warranted by the engine manufacturer.

This warranty includes the cost of parts and labor, but you must pay transportation
costs.

Instructions for Obtaining Warranty Service

If you think that your Toro Product contains a defect in materials or workmanship,
follow this procedure:

1.

Contact any Authorized Toro Service Dealer to arrange service at their
dealership. To locate a dealer convenient to you, refer to the Yellow Pages of
your telephone directory (look under “Lawn Mowers”) or access our web site
at www.Toro.com. You may also call the numbers listed in item #3 to use the
24-hour Toro Dealer locator system.

2.

Bring the product and your proof of purchase (sales receipt) to the Service
Dealer. The dealer will diagnose the problem and determine if it is covered
under warranty.

3.

If for any reason you are dissatisfied with the Service Dealer’s analysis or with
the assistance provided, contact us at:

RLC Customer Care Department

Toro Warranty Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

888-865-5676 (U.S. Customers)

888-865-5691 (Canada customers)

Owner Responsibilities

You must maintain your Toro Product by following the maintenance procedures
described in the

Operator's Manual

. Such routine maintenance, whether performed

by a dealer or by you, is at your expense.

Items and Conditions Not Covered

There is no other express warranty except for special emission system
and engine warranty coverage on some products.
This express warranty does not cover the following:

Cost of regular maintenance service or wear parts, such as filters, fuel,
lubricants, tune-up parts, blade sharpening, brake and clutch adjustments.

Any product or part which has been altered or misused and requires
replacement or repair due to normal wear, accidents, or lack of proper
maintenance.

Repairs necessary due to improper fuel, contaminants in the fuel system, or
failure to properly prepare the fuel system prior to any period of non-use over
three months.

Pickup and delivery charges.

General Conditions

All repairs covered by these warranties must be performed by an Authorized Toro
Service Dealer using Toro approved replacement parts.

Neither The Toro Company nor Toro Warranty Company is liable for indirect,
incidental or consequential damages in connection with the use of the Toro
Products covered by this warranty, including any cost or expense of providing
substitute equipment or service during reasonable periods of malfunction or
non-use pending completion of repairs under this warranty.

All implied warranties of merchantability (that the product is fit for ordinary
use) and fitness for use (that the product is fit for a particular purpose) are
limited to the duration of the express warranty.

Some states do not allow exclusions of incidental or consequential damages,
or limitations on how long an implied warranty lasts, so the above exclusions
and limitations may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.

Countries Other than the United States or Canada

Customers who have purchased Toro products outside the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country,
province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer. If all other
remedies fail, you may contact us at Toro Warranty Company.

Australian Consumer Law:

Australian customers will find details relating to the Australian Consumer Law either inside the box or at your local Toro Dealer.

374-0252 Rev E

Summary of Contents for 74901 Z Master 5000





































































Reviews: