Toro 74901 Z Master 5000 Operator'S Manual Download Page 13 | Manualshive

Page: 13 / 68

background image

Blade Control Switch (PTO)

The blade control switch (PTO) is used to engage the electric
clutch and drive the mower blades. Pull the switch up to
engage the blades and release. To disengage the blades, push
the blade control switch (PTO) down or move a motion
control lever into the neutral lock position.

Ignition Switch

This switch is used to start the mower engine and has three
positions:

Start, Run

and

Off

.

Motion Control Levers

The motion control levers are used to drive the machine
forward, reverse, and turn either direction.

Neutral Lock Position

The neutral lock position is used with the safety interlock
system to engage and to determine neutral position.

Fuel Shut-off Valve

Close the fuel shut-off valve (under the seat) when
transporting or storing the mower.

Attachments/Accessories

A selection of Toro approved attachments and accessories are
available for use with the machine to enhance and expand
its capabilities. Contact your Authorized Service Dealer or
Distributor or go to www.Toro.com for a list of all approved
attachments and accessories.

Specifications

Note:

Specifications and design are subject to change

without notice.

Width:

48 inch Deck

52 inch Deck

Without Deck

45.7 inches (116.1
cm)

45.7 inches (116.1
cm)

Deflector Up

54 inches (137.2
cm)57.5

57.5 inches (146.0
cm)

Deflector Down

63.6 inches (161.4
cm)

67.6 inches (171.8
cm)

Length:

48 inch Deck

52 inch Deck

Roll Bar - Up

79.2 inches (201.2
cm)

79.2 inches (201.2
cm)

Roll Bar - Down

80.9 inches (205.5
cm)

80.9 inches (205.5
cm)

Height:

Roll Bar - Up

Roll Bar - Down

70.5 inches (179.1 cm)

46.8 inches (118.9 cm)

Weight:

Model

Weight

74901

1120lb (508 kg)

74903

1168lb (530 kg)

13

«
...
11
12
13
14
15
...
»

Summary of Contents for 74901 Z Master 5000





































































Reviews:

No comments

Related manuals for 74901 Z Master 5000

Brand: Yard Machines Pages: 32

YP21KH42 (96041031300)

Brand: Yard Pro Pages: 20

Brand: MTD Pages: 16

Brand: Toro Pages: 52

Brand: Dixie Chopper Pages: 52

Brand: MTD Pages: 20

Brand: FGM Pages: 33

Brand: Walker Pages: 92

Brand: Encore Pages: 28

215012, 215014, R215012, N2151

Brand: Snapper Pages: 52

Brand: SaMASZ Pages: 37

Brand: Toro Pages: 48

Brand: Ferris Pages: 60

Pro Force Groundsmaster 3280-D

Brand: Toro Pages: 8

Brand: Hayter Pages: 36

Brand: Husqvarna Pages: 24

Brand: RHINO Pages: 156

Brand: Bushranger Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands