Toro 74901 Z Master 5000 Operator'S Manual Download Page 40 | Manualshive

Page: 40 / 68

background image

Servicing the Fuel Tank

Do not attempt to drain the fuel tank. Ensure that an
Authorized Service Dealer drains the fuel tank and services
any components of the fuel system.

Electrical System
Maintenance

Servicing the Battery

Service Interval:

Monthly

WARNING

CALIFORNIA

Proposition 65 Warning

Battery posts, terminals, and related

accessories contain lead and lead compounds,

chemicals known to the State of California

to cause cancer and reproductive harm.

Wash hands after handling.

DANGER

Battery electrolyte contains sulfuric acid which is a
deadly poison and causes severe burns.

Do not drink electrolyte and avoid contact with
skin, eyes or clothing. Wear safety glasses to shield
your eyes and rubber gloves to protect your hands.

Removing the Battery

WARNING

Battery terminals or metal tools could short against
metal machine components causing sparks. Sparks
can cause the battery gasses to explode, resulting
in personal injury.

•

When removing or installing the battery, do not
allow the battery terminals to touch any metal
parts of the machine.

•

Do not allow metal tools to short between
the battery terminals and metal parts of the
machine.

40

«
...
38
39
40
41
42
...
»

Summary of Contents for 74901 Z Master 5000





































































Reviews:

No comments

Related manuals for 74901 Z Master 5000

Brand: Snapper Pages: 1

Brand: Neuton Pages: 28

Commercial Front Cut Rider YHRK20

Brand: Yazoo Pages: 83

Jacobsen 744908A

Brand: Textron Pages: 34

Brand: Echo Pages: 244

Brand: Yard force Pages: 16

Brand: Alamo Pages: 168

Craftsman 917.250262

Brand: Sears Pages: 60

Brand: Yard Pro Pages: 108

NZMX30614KH, NZMX32734BV

Brand: Snapper Pages: 13

Tri King 1900 Series

Brand: Jacobsen Pages: 30

Brand: Woods Pages: 28

Brand: Ariens Pages: 29

Brand: Worx Pages: 24

Brand: Gardif Pages: 22

Brand: GARDTECH Pages: 10

GRASS 1265 ZSBW

Brand: Garland Pages: 172

Time Saver i1042

Brand: Cub Cadet Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands