TNI 40610021 Instructions For Use Manual Download

Page: 26 / 40

Instructions for Use

TNI

soft Flow

Clinic System

605

Air flow too hot

Therapy air temperature is too high. Please

check environmental conditions and refer to

the product specifications.

606

Applicator heating defective

Hardware error.*

651

Applicator heating defective

Applicator heating is defective; please replace

by a new applicator.

652

Applicator not found

Applicator cannot be detected; please replace

by a new applicator.

653

Applicator type

The selected flow rate is too high for this type

of applicator; reduce flowrate or use a larger

applicator.

654

Applicator type

The selected flow rate is too low for this type

of applicator; use a smaller applicator.

655

Applicator not supported

The connected applicator is not supported by

this device. Please use an applicator accor-

ding to accessories table in chapter 1.4

701

System failure

EEPROM (internal memory) is defective.*

702

System failure

Operating system error.*

703

System failure

EEPROM (internal memory) is defective.*

704

System failure

User settings are damaged.*

705

System failure

Firmware error.*

706

Wrong hardware

Hardware error.*

707

System failure

System error.*

708

System failure

EEPROM (internal memory) is defective.*

752

SD card or file defective

SD card checksum error; please change SD

card and restart system. If error persists, cont-

act your TNI medical AG representative.

753

System failure

Battery voltage is too low.*

754

System failure

Firmware checksum error.*

755

System failure

Firmware error. Please remove SD card and

contact your TNI medical AG representative.

756

Font could not be loaded

Font of selected language cannot be loaded.

File is defective or missing. Please select

standard font (English, e.g.). Contact your TNI

medical AG representative for further help.

757

Low SD card memory

Please insert a new SD card.

851

Change dust filter

Change the dust filter.

If the fault persists, contact your TNI medical AG representative.

Summary of Contents for 40610021









































Search results

Summary of Contents for 40610021

Reviews:

Related manuals for 40610021

Brands by name

Popular brands

TNI 40610021, Instructions For Use Manual

Search results

Summary of Contents for 40610021

Reviews:

Related manuals for 40610021

Brands by name

Popular brands